The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes properly, the rack s...
Sold individually. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking, or tilting forward.
This manufacturer-certified heating element is used to create heat during the dry cycle and increase water temperature during portions of the wash cycle when certain options are selected. If your dish...
The rinse aid cap (sometimes referred to as the dispenser cap), covers the rinse aid dispenser on the dishwasher door. If your dishwasher will not dispense detergent, or it is leaking detergent, there...
This part is used as a safety device to protect the dishwasher circuit from overload. If the temperature gets to high it will shut off the electrical current to the heating unit in the appliance. Als...
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Michael
March 4, 2024
Why does my dishwasher stop with a long delay and start and stops shortly after it starts I changed the control board and reset it but middle way it stop and start
For model number DU1055XTVS0
Hi Michael, thank you for reaching out. We have found that the issue is with door switch, part number PS11745501. It detects when the door is closed so the dishwasher can start. You may need to replace the switch to fix the issue. Glad to be of assistance!
What controls the temperature during the washing cycle? Dishwasher overheats during washing (high temperature sensor replaced) and no problems during the drying cycle at end. Is the turbidity sensor the problem and should I pull and clean it? Is there a different sensor somewhere?
For model number DU1055XTVS0
Hello Roger, Thank you for the question. Turbidity sensors measure the amount of light that is scattered by the suspended solids in water and should not effect the heat. If the Thermostat did not fix the issue, the Electronic Control Board is what controls the temperature of the water and the cycles. We hope this helps!
The wash cycle continues to run and won’t move to the next cycle. What might be the cause?
For model number DU1055XTVS0
Hello Russell, thank you for reaching out to PartSelect. Make sure the heating cycle is working fine. First, try checking the temperature reading on your water heater. The temperature should be somewhere between 120? (49°C) and 130? (54.4°C). If not, you will need to replace the high limit thermostat, part number PS11743423. Good luck with this repair!
Where is the filter for this DW and how do I clean it? Thank you.
For model number DU1055XTVS0
Hi Kelly,
Thank you for your question. The filter for the dishwasher is found on the sump. Here is a link to one of our YouTube videos that you may reference for information on where the filter is located and how to remove and install it. We hope this helps!
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
I did a search on the website and read the instructions for trouble shooting. I took the inside door off by taking the screws out. I pulled the part and tested it and found it did not in fact have no ampage. I then ordered the part on line. It came in two days, I plugged it in, put the door back together and the total time was about 15-20 minutes. Easy, simple, great instructions and the entire thing only costed me the part itself. It's working great now! And I've never worked on appliances before.
