Models
>
DE7400
DE7400 Dryer - Overview
Models starting with DE7400
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Drum Support Roller Kit
PartSelect #: PS1570070
Manufacturer #: 12001541
This drum support roller includes one drum roller and two bearings. Most dryers use two drum rollers, and it is recommended to change both at once.
$19.12
In Stock
Rear Drum Bearing Kit
PartSelect #: PS459829
Manufacturer #: 5303281153
This kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws.
$71.08
In Stock
Tumbler and Motor Belt
PartSelect #: PS11757542
Manufacturer #: WPY312959
The tumbler and motor belt in your dryer allows the drum to spin during the drying cycle. At 100 inches in length, this dryer drum belt is 3/8 of an inch wide and has five ridges. The belt is black in...
$41.42
In Stock
Drum Belt
PartSelect #: PS1148434
Manufacturer #: 134503600
This 88 3/4 inches long and 1/4 inch wide dryer drum belt goes around the dryer drum and the pulley to rotate the drum once the motor is activated.
$22.52
In Stock
Roller Shaft
PartSelect #: PS11743031
Manufacturer #: WP6-3129480
This roller shaft is the axle for the drum roller, also known as drum roller axle.
$12.51
In Stock
Front Glide Kit
PartSelect #: PS1804752
Manufacturer #: 306508
This front glide kit comes with a blue plastic glide, a brown cork pad, and two metallic rivets. Two kits are required per appliance. A rivet tool is required for this installation.
$18.74
In Stock
Blower Wheel with Clamp
PartSelect #: PS2200270
Manufacturer #: Y303836
This blower wheel comes with a metallic hub clamp to hold it firmly in place.
$29.17
In Stock
Upper Drum Glide
PartSelect #: PS470317
Manufacturer #: 5303937139
Front upper felt glide pad with 3 nylon glides - includes adhesive.
$44.37
In Stock
Retaining Ring
PartSelect #: PS11746909
Manufacturer #: WP9703438
This metallic retaining ring is less than an inch in diameter. It is made entirely of metal.
$10.05
In Stock
Lint Filter
PartSelect #: PS11741140
Manufacturer #: WP33002970
This filter collects lint as it passes through the dryer vent.
No Longer Available
Drum Support Bearing
PartSelect #: PS418807
Manufacturer #: 131825900
This part attaches onto the inside of the rear panel of the cabinet.
$8.07
In Stock
Thermal Limiter - Limit 220
PartSelect #: PS419402
Manufacturer #: 134120900
This thermal fuse limiter, with a limit of 220 degrees Fahrenheit, is manufactured for both gas and electric clothes dryers. Once the internal temperature of the dryer reaches 220 degrees, the heating element cuts out.
$34.73
In Stock
Common Symptoms of models starting with DE7400
[Viewing 6 of 6]Noisy
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Too hot
Fixed by
these parts
these parts
Show All
Drum Not Spinning
Fixed by
these parts
these parts
Show All
Won’t Start
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
noisy rollers, broken latch
first, I unplug the power supply of the dryer then I removed the two screws at the bottom of the dryer then pulled out the front part of the dryer,unplugged the blue & yellow wire for the on/off switch for the door,at the back of the dryer I unscrew the pannel for the belt,disconect the belt,and I unscrew the four screws on both side of the front pannel to remove the front cover of the drum. Once I removed the front cover of the drum I can now remove the drum itself to access the drum support roller. I unscrew the rollers then replace it with the new once. It was an easy job.
Thank you.
Thank you.
Parts Used:
-
gerry from west covina,, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Wrench (Adjustable), Wrench set
648 of 675 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The blower fan (nylon) stripped off the motor shaft (steel)
Removed the front cover (screws on bottom 0f face)...removed blower cover....spring pliers to remove and install blower fan. the rest of the time was spent cleaning the inside of the shell as well as the vent. Reassembled and dryer runs better than it has for many years.
Parts Used:
-
Stephen from Lafayette, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers
565 of 571 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Squealing noise
We followed the instructions for the drum glide replacement and changed the belt and drum support bearing piece, cleaned it out too. Works like a charm. Thanks for saving us a bundle.
Parts Used:
-
Cynthia from Lexington, SC
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Wrench (Adjustable), Wrench set
529 of 551 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!