This is a flood switch assembly for your washer. The flood switch controls the hot and cold water filling your washer tub to ensure the proper amount of water. You may need to replace this part if you...
This is replacement door latch for your dishwasher. The door latch is attached to the tub frame, and connects to the door strike to keep your dishwasher door closed during operation. If you have a bro...
This is a genuine GE Beach Gasket for your dishwasher. This part creates a seal on your dishwasher door, and prevents the door from leaking water. If your old gasket is loose, installing a new one is ...
The drain hose elbow carries water from the sump to the drain pump. If the waste water is not draining from the dishwasher, there could be an issue with the drain hose elbow. Check the drain hose for ...
This is a genuine GE dishwasher leveling screw. It operates as a leg on the bottom of your dishwasher, and can be screwed in and out to raise and lower the height of the dishwasher. It is made of meta...
This is a lower rack roller for your dishwasher. It attaches in the lower roller assembly on the bottom of your rack to allow the rack to smoothly slide in and out. This replacement part is 1.5 inches...
We tried cleaning out the filter and it clogged with a huge amount of gunk. We removed the gunk, scrubbed the filter, and tried running the dishwasher, but still no water. That took over an hour (not counting the time the dishwasher spent running). Then we tried your diagnosis center and it pointed to the flood switch or the water valve. I extracted the flood switch (another 30-60 minutes) to check it, and it also contained gunk and (significantly) did not rattle, which made me suspect the flood switch was the problem, so I ordered one. Once the replacement arrived, I checked it and the flood switch rattled, confirming that it should work properly. I spent 30-45 minutes installing it, plus the filter assembly and racks I had to remove to access it. Ran the dishwasher and everything came out sparkling clean. I don't know where the gunk came from, but if you aren't getting water and the filter is full of gunk, check the flood switch.
I replaced the tub gasket around the door circumference which took less than five minutes to replace. However the problem was replacing the beach gasket that prevents the water from flowing out of the dishwasher tub. The door had to be unhinged from the dishwasher which was unscrewed from the cabinets and brought out from its location. After the door was completely removed it was laid on its front. After removing the door hinges which were secured with just one bolt I tried to slide the back panel off the front panel but without any success. So I had to remove the torn and worn out gasket while working in a tight space. This is where the problem rose because according to installation instructions there are screws supposed to be holding it to the main body frame. However, in my case rivets were used by the manufacture since this was the first time the gasket was being replaced. So I had to use a power tool With a grinding bit to remove the face of the rivets and essentially cut them out to reveal the underlying holes. After this I replace the beach gasket and then used half inch SS Philips bolts and nuts to secure the gasket to the body frame.
1. Turn off breaker supplying power to dishwasher in electrical panel 2. Open dishwasher door 3. Unscrew the screws that secure the dishwasher to the counter. 4. Tip dishwasher forward. Identify the non-functioning door latch. It looks exactly like the replacement. Unclip the wire harness from the door latch. 5. On the inside of the dishwasher, there are 2 screws directly under the door latch. Unscrew them and carefully set aside. 6. Remove old door latch. 7. Set new door latch in place. Holding securely, replace screws removed in step 5. Toward the end they get a little tougher to screw in. 8. Plug wire harness into new door latch. 9. Re-align dishwasher and re-secure to counter in previous position. 10. Test latch to make sure it closes properly. 11. Turn on breaker in electrical panel. The dishwasher should now function properly.
