CDB500NB5B Crosley Dishwasher - Instructions

Repair was simple. I unscrewed the old grommet which held the old spray arm and screwed-on the new one. About 30 seconds was required. Other people having this problem should note that the spray-arm is made of three pieces which are inseparable when the arm is new. The arm is sold in this form. However, when your machine is having the problem that the arm falls off, the three pieces become separate. When you want to replace the spray arm, only one new part needs to be ordered because this part encompases all three components.

Took the roller out of the package, snapped it into place. Less than 15 seconds. Works good as new.

I have had to keep replacing the spray arm on the bottom of my dishwasher which takes like 2 seconds to do.. First you open the dishwasher and than pull the bottom basked forward and reach down and pull the spray arm up and pop the bottom of the spray arm off and put it on the new spray arm and slip it back into the dishwasher over the thing that makes it spin around.. but the tricky part is and I didn't know this and this is why my dishwasher spray arm kept falling over and melting on the heating element.. you have to turn it till it clicks in.. and your done..

I removed old tub gasket, which the door presses against to make a seal, and put the new one in. Flat tip screwdriver was used to gently press gasket in.

It was amazing, the items were shipped within days of placing the order. They arrived ready for installation. My husband had the new racks in place in 10 minutes. He removed the wheels from the old racks and placed the wheel on the new racks which required no tools. Then we slid the new racks into place, a perfect fit!

Unscrewed retaining ring, replaced unit = piece of cake

The hardest part was disconnecting the dishwasher. the motor is located on the bottom so after pulling it out and laying it down on the front of the machine the motor unplugs and 2 screws hold it in place.The new motor comes with "O" rings so I applied a little grease and put it back together. 2 minutes to replace motor, 15 minutes to disconnect water and electric, 15 to reconnect.

I looked under and found that 2 brass nuts that secured the heater element through the base housing of the dishwasher has split down each side of the nut and no longer was tight enough to keep water from leaking around either end of the heater element. I powered down the dishwasher at the circuit breaker and then reached under the dishwasher and pulled away the 2 wires that were attached to each side of the heater element. I removed the two nuts and replaced them with the parts I ordered from partselect.com. I then put the appropriate wires back at the end of the heater element and ran the dishwasher to check for leaks. No leaks... it was fixed.

It required no tools. It took less than one minute to connect the spray arm to the bottom of the unit. Our dishwasher is working perfectly now.

It was simple, I do have extended warranty from AHS, but they charge me a trip charge of $55 per repair, and then all parts and labor is covered. But when I checked with Parts Select the parts costed me about $10, so I decided to do it myself.

While I was at it, I also bought other parts and updated my dishwasher with some upgrades.

Good place to buy any parts from, they are very helpful, if you do not know your parts. They even had drawings of my dishwasher, and this actually helped me find what kind of other parts I could buy to upgrade my dishwasher.

Parts select is on my favorites list and pass it on to all my friends.

First, I had to remove a small metal paper clip that somehow ended up in the bottom of the dishwasher, which jammed the spray arm. The spray arm wasn't able to spin around, so it melted onto the heater. I removed the spray arm, and replaced it with the new one.

simple repair..woke up one morning and after the dishwasher cycled, I noticed the upper spray arm laying on the top tray.
ordered new one from site, was delivered with-in 2 days ( with standard shipping) all 1 piece, took seriously 5 seconds to unscrew by hand and replace!

See posting under O rings. Get schematic Motor & Pump pg. 8 from pub # 5995487674. Steps: 1) run cycle so most water is pumped out of dishwasher 2) remove front cover to reduce weight of door; 3) disconnect electric plug, hot water hose [NOTE: be prepared for some water from hose], and waste tube all usually found under sink area; 4) remove 2 screws at top of front panel; 5) lower leveling feet to allow best clearance; 6) put towels under front feet to protect floor and slide unit out from under counter; 7) place heavy blanket next to unit to protect floor and tip unit over on its side; 8) disconnect electric plug from motor and remove metal spring clip holding motor (2 torx screws) and pull clip off motor; 9)gently rock motor while lifting to remove from unit [NOTE position of motor for reassembly]; 10) put thin coat of silicon on O rings and place on new motor [look at old motor to make sure O rings are in proper slots; 11) line up motor and gently push new motor back into position; 12) reverse disassemble steps above. 13) run dishwasher through fastest cycle to check for leaks.

First I just rolled out the lower rack assembly, and rolled the new one in. Then I moved onto the upper rack. I started by sliding the off the rail cap lock at the end of the rack. The entire cap does not come off, just the bottom slotted piece. This is done by simply edging out the bottom of the cap, toward the front of the dishwasher, until the bottom slides out of the slot, and lifts out of the way. Then the upper rack was released to roll freely out of the support rail. The next step was to pry off the top of the water diverter. Next was to unscrew the wand assembly from the water diverter that is attached to the upper rack assembly. There are no water lines attached to this, it just directs the jetted water from the top of the dishwasher. Then simply pop the mount from the upper rack. And reassemble the way it came off. This was a simple fix to make the dishwasher like new inside again. The racks purchased from Parts Select fit perfectly with no modifications or trouble. This operation took less than ten minutes. Anyone should be able to handle this operation. If you are afraid to disassemble the upper rack, take a few digital pictures to refer to, and delete them later. This is a tip that has been priceless to me in the past on other projects. Thank you Parts Select.

My friend bought a used dishwasher at a garage sale, the previous owner had thrown away the drain hose because it was "nasty" they said....remember it could have been cleaned. When I went to install it, I removed the old washer, and discovered that the old hose would not fit on the replacement dishwasher. I went to the local repair shop, armed with the model and serial #'s. they searched and searched their books and could not find the hose part number. they said "good luck" when I left...I went home and looked up the model on your web site, ordered the hose, and in 3 days had the dishwasher installed and running in about 30 minutes...thanks for prompt shipping.. I couldn't believe it arrived so soon...Mowerman