All Installation Instructions for General Electric Range CCGS986SEL1SS

Oven Lamp Holder Burned

removed two phillips screws. Unplugged electrical connections replaced unit from PartSelect. They sent holder cover and new bulb (surprise). Great store with great directions.

Parts Used:

Oven Light Housing

Jack from Okmulgee, OK
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

23 of 28 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

oven post mini explosion sounding

the flame spreader through the years, developed a hole above the glow coil causing the above trapped gas between the oven pan and spreader to ignite. by replacing the flame spreader the problem is gone and is now working properly. thank you, parts select for being there when i needed the part and also being reasonably priced. mike marino

Parts Used:

DEFLECTOR OVEN

Mchael J. from Chesterfield, VA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

13 of 22 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven light did not work

Turned off power to the oven, Removed the oven light housing, installed new housing, turned power on and walla.

Parts Used:

Oven Light Housing

Howard from Rio Vista, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

9 of 16 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Original burner cap was chipping; must have been dropped somewhere along the line.

New burner cap replaced old; just placed over burner; no tools required.

One suggestion: burner cap should have been shipped with thicker bubble protection (easy to do). It was minimally wrapped and placed in a thin, bubble envelope, risking damage in shipping process. Luckily, the burner arrived in tact and usable.

Parts Used:

Burner Cap - 15K

Mitzi from Briarcliff Manor, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

8 of 13 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

wire connection to socket was bad

Disconnected the old socket ( 2 srews ) removed the two wires from the old socket, reconnected them to the new socket and reinstalled the lamp.

Parts Used:

Oven Light Housing

David from Gansevoort, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

6 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Gas oven was not lighting (bake only)

Repair was very easy. 2 screws to remove the bottom cover inside the oven. 2 more screws to remove the igniter. Cut the wires to remove it from the back of the oven. 3 screws to remove the back cover. Un-clipped old igniter , pushed new one through the hole (from inside the oven). Connected and re-applied screws. Worked like a charm.

Parts Used:

Oven Igniter - Bake

Jerry from MACOMB, MI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

5 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Hole burned through deflector oven and metal dropped onto igniter and burned it out

Removed bottom shelf from inside oven, turned it obj and replaced the oven deflector with only a screwdriver

Parts Used:

DEFLECTOR OVEN

Scott from ARDMORE, PA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

5 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Light not working tried to Remove light assembly not knowing glass could screw out. Without thinking grounded exposed hot wire to burner bracket melting light socket connector. Had to replace socket.

First and most important trun off curcit breaker. Use 1/4 inch but driver to remove socket (2) screws. Remove ground and hot wire clips from old socket, replace on new socket. Screw back into oven ceiling and turn on power. Reset clock and your are done. Very simple.

Parts Used:

Oven Light Housing

Richard from CUMMING, GA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Missing grate foot / bumper

Put in a new foot / bumper. That's it.

Parts Used:

Burner Grate Foot

Irene H from HENRICO, VA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

6 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven Light Assembly damaged

I have a double oven and coincidently I had to replace the two Oven Light Assemblies.
I am really glad about your web site because once I got the number from my oven model you guys were the first ones that came up. Thanks to your prompt and reliable service my oven is back to its original state.

Jose Figueroa

Parts Used:

Oven Light Housing

Jose from Frederick, MD
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers

5 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Large burner cap finish was damaged

Just lifted old burner off with my fingers and replaced with the new one. What needs to be focused on here is the fact that Part Select has such a complete line of parts rather than the difficulty in the install.

Parts Used:

Burner Cap - 15K

Richard B from CLARKSBORO, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

One burner would not light from spark. All other burners lite with spark.

First I checked that the wire and sparker was working by switching the wires on top of the range. I did this by pulling out the sparker switching it from the back working burner on the same side. The same burner would not light so I knew it was not the sparker.

Then watch a bunch of videos and found this gal to be the most helpful on how to take apart my exact stove.
Go here: https://www.youtube.com/watch?v=WRGfuhUzEaY

I did not take everything apart like she did. I ordered the spark module and just replaced it following her method to take off the back, switch the wires to the new module, then put everything back together again.

All burners have been working perfectly since the fix.

Parts Used: