The bake element is located on the bottom of the oven. If your oven will not heat properly it may be due to a faulty or damaged baking element. If you can see that the element has been separated or blistered, you should replace the part immediately. If there is no visible damage, turn the oven on and check to see if the element heats even...Read morely. If the element is not heating evenly, or if it is not heating at all, it will need to be replaced. This element is 19 inches wide x 19 inches long, and has male spade push on terminals.
This surface burner head is for ranges.
Surface burner head distributes the gas through holes or slots to create an even flame across the cooking area.
Shut off the gas supply and unplug the range before installing this part. Wear work gloves to protect your hands.
This is a replacement burner cap for your gas range or cooktop. The burner cap is found on the burner head, and prevents debris from getting into the head when it is not in use. The cap is black in color and is sold individually. It is a little more than 4 inches in diameter. To replace the burner cap, simply remove the damaged cap, and r...Read moreeplace it with the new one. No tools are required for this repair. This is an OEM part from the manufacturer.
This burner cap is for your gas range, and acts as a cover for the burner head. It is black in color and just over 3 inches in diameter. If your old burner cap is damaged or missing, this is the part that will replace it. This is an OEM part sourced directly from the manufacturer and is sold individually.
This knob accepts a D-shaped shaft. Sold individually.
NOTE: The manufacturer has updated this knob. It may be smaller than the original but will function the same.
This is a replacement vision burner or surface burner head for your gas range. It is silver in color and approximately 4.5 inches in diameter. This burner is sold individually. The burner head distributes gas to create an even flame across the cooking area. If you notice that your food is not cooking evenly, or you are not getting an even...Read morely distributed flame, you may need to replace the burner. The burner is located beneath the burner cap, below the grate. To remove the burner, simply remove the grate and the burner cap, then lift the burner head out. Replace it with the new burner, and reinstall the cap and grate. This is an OEM part sourced directly from the manufacturer.
If your oven isn’t getting hot enough when you broil, this replacement broil element could be the fix. It’s the part that heats from the top of the oven to give food that crispy finish. Easy to install—just make sure it fits your model and turn off the power before starting.
This is a burner cap for your gas range. The cap is black in color and about 3 inches in diameter. The cap acts as a cover for the burner head. If your old burner cap is damaged or missing, this is the part that will replace it. This is a quality OEM part sourced directly from the manufacturer. This cap is sold individually.
The rubber bumper sits between the burner and the range itself to ensure the burners do not scrape the stove top. This OEM replacement bumper is sourced directly from the manufacturer, and is sold individually.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Colum - For model number C2S985SET1SS
January 30, 2023
The touchpad on my dual fuel range works but the lighted display only lights intermittently. Firmly pounding on the top of the range will often cause the control panel to illuminate. I opened up the range to access the back of the control panel but cannot find any loose wires or obvious electrical shorts. What part do I need to replace to fix this problem?
Hello Colum, thank you for contacting us. The issue is probably related to a faulty control board, part number PS8754524. We would recommend checking it with a multimeter to pinpoint the fault. Please reach out to customer service if you need help placing an order. Glad to be of help!
Looking for the burner for this gas stove. Front right- 4.5 inches. I have a picture of if will help.
Hi Ron, thank you for your inquiry. We have found that the right front burner contains 3 parts: the surface burner head, part number PS3650622, the outer burner cap, part number PS3503823, and the center burner cap, part number PS3503824. You may order the part that you need. We hope this helps.
Our GE cafe free standing dual range turns itself off in the middle of baking at temperatures above 375 degrees. What can be the problem?
Hello Doug and thank you for writing.
It certainly sounds like it could be a faulty temperature sensor PS236490, you should check for signs of damage, and replace if necessary. We hope this helps. Please contact us anytime if you require further assistance.
How do you remove the oven slide do i can adjust the door spring tension? Thanks
Hello David,
Thank you for your question. There should be two brackets on each corner of the bottom part of the door that you can unscrew to slide the door out. You may need to unscrew the hinges as well to be able to adjust the springs. We hope this helps.
Was this helpful?
Thank you for voting!
Brent - For model number C2S985SET1SS
December 23, 2021
I need to replace the plastic part to the #2 knob. The shaft of the plastic part broke off when the knob was forced too hard.
Hello Brent, Thank you for the question. The Plastic Shaft is only sold as part of the Knob, PartSelect Number PS2339711. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Lower bake Element would not heat.
230 of 264 peoplefound this instruction helpful.
Ronald from Nassau, NY
Really Easy
Less than 15 mins
Nutdriver, Pliers
First I slid the stove out and unpluged it, then removed two screws,slid out element, disconected two wires, slid new element in to place, pluged two wires in ,put into place and installed two screws, pluged stove back in, and turned on to try. Works perfect.
Was this helpful?
Thank you for voting!
Broken heating element
75 of 93 peoplefound this instruction helpful.
Paul from anna, TX
Really Easy
15 - 30 mins
Nutdriver, Pliers
1)Turn off power to stove 2)remove 2 bolts holding heating element 3)pull element out of the back of the oven about 8" so that the wire connects is visable 4)pull wire clips off of heating element and remove element from the oven 5)put wire clips on the new heating element 6)push new heating element back into the
... Read moreholes in the back of the oven 7)screw botls back into the oven holding the heating element in place 8)Turn power back on
Read less
Was this helpful?
Thank you for voting!
terminal block melted
56 of 77 peoplefound this instruction helpful.
jonathan from willow springs, IL
Easy
Less than 15 mins
Nutdriver, Screw drivers
The existing terminal block on my Ge oven/Range had melted due to a loose wire causing sparking and starting the plastic casing of the terminal block on fire and melting it, Part select made the part easy to find and had it at my house in 2 days. All I had to do was remove six screws to take the back sheet metal cover off of the oven. U
... Read morenscrew the terminal connections remove two mounting screws that held the terminal on to the oven body. This was a little trickier than it should have been because the melted plastic had reformed making it very hard to access the mounting screws. i then mounted the new piece and plugged the oven in, it took 15 minutes and was very easy. definitely saved me at-least a $100 for the service call i would have made if finding the part wasn't so convenient
My Orders
