BGHS2644KF2 Frigidaire Refrigerator - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Refrigerator Water Filter – Part Number: ULTRAWF
$132.79
In Stock
Refrigerator Water Filter
★★★★★
★★★★★
(51)
Part #ULTRAWF
This genuine PureSource Ultra water filter will fit most Frigidaire french door and side by side refrigerators. You will find this filter located in the back, top right of the appliance. It is white in color and the filter has a polypropylene plastic housing and extruded carbon block filter media. Certified by NSF/ANSI to reduce contaminants that may be in your household water supply by 99.8 percent. The operating temperature for this filter is 33-100 degrees Fahrenheit, the flow rate is 0.5 GPM, the working pressure is 30-100 PSI, and it has a micron rating of 1. This filter should be replaced every six months or when the indicator lights up red. Installation is quick and easy. Push on the end face of the older filter to allow it to release. Remove and discard the old filter. Slide the new filter into the housing and press it down until it locks into place. Be sure to run water through the dispenser for about three minutes to prime the filter before use. Discard this water or use it to water plants. Do not forget to reset the indicator by pressing it down for 3-10 seconds. Review the use and care guide before you install for more detailed instructions.
Crisper Cover Support - Front – Part Number: 241993101
$16.27
In Stock
Crisper Cover Support - Front
★★★★★
★★★★★
(17)
Part #241993101
This crisper cover front support is used to keep the crisper shelf in place and may need replacing if the door will not open or close. This white, OEM part measures roughly 1 inch in diameter and can be used for the front and the rear support, as designed by the manufacturer, and mounts to the inside cabinet wall. Replacing this part is an easy repair, and will require a small flat blade screwdriver, a putty knife, and a soft hammer. Remove the crisper and shelf from the refrigerator before replacing the support. The crisper cover front support is held in place with a locking pin. To remove the old part, you will first need to push the pin into the interior of the cabinet using the screwdriver, and then you can pull the support out with a putty knife. If you cannot get the pin out you can use a flat-blade screwdriver to push it down and out of sight and it will not harm anything in your refrigerator After removing the pin and attaching the new support, simply use the soft hammer to lock the new pin in place.
Bottom Door Bin – Part Number: 240323002
$87.95
In Stock
Bottom Door Bin
★★★★★
★★★★★
(25)
Part #240323002
The Bottom Door Bin is also commonly known as a "cantilever shelf" is a clear plastic drawer which holds items in the bottom area of your fridge's interior, on the door. This OEM part is very easy to install and will not require any tools, you will just need to snap the mounting tabs into place for removal and installation. If damaged you will notice visible damage or have problems holding items in the fridge. If damaged, it should be replaced. Check your model number and user manual to see if this is the right part for you. This is important, as many fridges use multiple door bins, many of which vary slightly. This part is sold individually.
Crisper Support - Rear – Part Number: 241993001
$22.95
In Stock
Crisper Support - Rear
★★★★★
★★★★★
(4)
Part #241993001
This authentic rear crisper support is a white, plastic part which is rated as "easy" to install by our customers. This OEM part replaces the rear crisper cover support in your fridge and mounts to the inside cabinet wall. If there is visible damager or your crisper stops fitting properly, it may be time to replace the part. Check your user manual and model number to ensure this part is what you need. Replacing the rear crisper support in your refrigerator is an easy job. This part is made from plastic and mounts on the inside of the wall. To complete this repair you will need a small putty knife, a punch or a short flat blade screwdriver, and a small hammer. You may need to replace your rear crisper support if you find that the door will not open or close. In order to complete this repair, you will need to remove all the shelves above the crisper in order to have ample room to work. It is also good to have duct tape on hand, which can be used to protect the liner around the support. This part is sold individually. Please note that the rear and front crisper support are different parts; this is the one you are looking for if it is your rear support that needs replacing.
Meat Drawer Rail - Right Side – Part Number: 240356501
$69.57
In Stock
Meat Drawer Rail - Right Side
★★★★★
★★★★★
(23)
Part #240356501
This replacement drawer slide rail is for the right-hand side of your refrigerator. This part attaches to the inside wall of your refrigerator to support the sliding crisper drawer. If the rail is broken or the drawer is not sliding properly, you will need to replace the slide rail. You will need a Phillips screwdriver to complete this repair.
Refrigerator Water Inlet Valve – Part Number: 242252702
$104.89
In Stock
Refrigerator Water Inlet Valve
★★★★★
★★★★★
(54)
Part #242252702
This part releases water from the supply line when it's activated. NOTE: This part may appear different than the original, but is an authorized manufacturer replacement.
Meat Drawer Rail - Left Side – Part Number: 240365401
$70.26
In Stock
Meat Drawer Rail - Left Side
★★★★★
★★★★★
(17)
Part #240365401
This drawer rail supports the left hand side of the sliding drawer. The mounting screws are sold separately.
Light Bulb – Part Number: 316538904
$35.95
In Stock
Light Bulb
★★★★★
★★★★★
(9)
Part #316538904
This 40-watt appliance light bulb is a reliable replacement for use in select ranges, refrigerators, freezers, and microwaves. It provides bright, consistent lighting to help you see clearly inside your appliance. Installation is simple—just unscrew the old bulb and replace it with the new one. If the existing bulb is broken, disconnect power and use needle-nose pliers to safely remove the remaining base. Sold individually, this bulb is a commonly replaced part—consider keeping a spare on hand.
Defrost Thermostat Kit – Part Number: 5303918214
$48.80
In Stock
Defrost Thermostat Kit
★★★★★
★★★★★
(17)
Part #5303918214
This kit includes the clip, leads and one heat shrink.
Door Shelf – Part Number: 240351601
$65.26
In Stock
Door Shelf
★★★★★
★★★★★
(3)
Part #240351601
This original equipment manufacturer Door Shelf is a white plastic part which holds items inside of your freezer or refrigerator door. It is roughly 10 inches long by 4 inches high by 5.5 inches wide. It can be used in the freezer or refrigerator and is very easy to repair. All you need to do is snap the new door bin into place, which requires no tools. This part is sold individually and not as part of a set, even though your refrigerator may take more than one of this part.
Door Bin - Clear – Part Number: 240356402
$128.61
In Stock
Door Bin - Clear
★★★★★
★★★★★
(6)
Part #240356402
This bin can be moved according to space needed. It holds items on the door of your refrigerator. NOTE: This bin is only available in clear plastic now.
Refrigerator Light Bulb – Part Number: 5304517886
$88.98
In Stock
Refrigerator Light Bulb
★★★★★
★★★★★
(6)
Part #5304517886
This 3.8-watt LED light bulb is designed to illuminate the interior of select refrigerator models, providing bright and efficient lighting when the door is opened. If your current bulb is dim, flickering, or no longer functioning, replacing it will restore visibility and convenience. Installation is simple—unplug the refrigerator, unthread the old bulb, and screw in the new one. This bulb is sold individually and does not include additional components.

Manuals & Care Guides for BGHS2644KF2

Click to download

Common Symptoms of the BGHS2644KF2

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
water leaking out of refrigerator
608 of 723 people found this instruction helpful.
  • Jose from Alexandria, VA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Wrench (Adjustable)
In my specific appliance the water valve is located in the bottom right hand corner looking at it from the back. To get to it I remove the thin layer of cardboard the covers the back of the fridge. I then proceeded to disconnect the 1/4" copper tubing which is the water feed coming out of the wall. Then I removed the screws that hold the valve assembly in place. I took the water valve out and removed the electrical connections as well as the plastic tubing which feed the water dispenser and the ice maker. To install the new water valve it was just a matter of reversing steps.
Was this helpful?
Thank you for voting!
Tab on bottom door bin broke off
541 of 573 people found this instruction helpful.
  • Mark from Redlands, CA
  • Really Easy
  • Less than 15 mins
Replaced bottom door bin being careful not to put stress on the tabs to fit into molded area in door.
Was this helpful?
Thank you for voting!
freezer shelf broke
506 of 533 people found this instruction helpful.
  • MONICA from LANCASTER, CA
  • Really Easy
  • Less than 15 mins
Easy slide it back in place
Was this helpful?
Thank you for voting!