This is the replacement charcoal filter for your microwave. It is silver and black in color and measures approximately 10 inches by 2 ½ inches. The charcoal filter removes cooking odors from the air that circulates through the microwave vent. You will likely need to replace the charcoal filter if you notice any damage to it, or if it has...Read more been in your microwave for a long time. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.
This is a genuine replacement 40 watt bulb for a microwave. The bulb is meant to light up the underside of the microwave or inside of your microwave when the door is open or during use. If your bulb is not illuminating, you may need to replace it. If the bulb is shattered, be sure to use protective gloves during replacement. Always unplug...Read more your microwave before completing any repairs. We suggest ordering a spare, as this is a common wear part.
Uneven tray movement or loud rattling can be caused by a cracked roller ring or a wheel that no longer turns. The ring supports the glass tray and helps it rotate smoothly during cooking. First remove food buildup and check the tray, center drive piece, and oven floor for damage. Match the replacement to the full appliance model because r...Read moreing size and wheel position can vary. Disconnect power before inspection and handle the glass tray with care. Set every wheel flat in its guide, then turn the tray by hand to check its movement.
This turntable motor is for microwaves.
The turntable motor rotates the glass tray inside the microwave oven.
Because high-voltage capacitors in a microwave can retain a lethal electrical charge even when the microwave is unplugged, a service technician should install this part.
If your microwave suddenly stopped working, this 20-amp fuse might be the reason. It’s designed to blow when there’s a power surge, protecting your appliance from damage. This genuine part fits many GE, Hotpoint, and Frigidaire models. Just check your model number before replacing it.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mary - For model number AVM4160DF1WS
February 4, 2020
Does the light screw in or pull out?
Hello Mary, Thank you for the question. The Bulb PartSelect Number PS8767095 is screw in. We hope this helps.
Microwave went off while in use we checked the place it was plugged in and had power. Interior light doesn’t come on nor does the display. No noise when u push buttons
Hi Jeffrey, thank you for reaching out. The issue seems to be with the control board, part number PS8754630. It is imperative for managing significant microwave operations such as heating, lighting, and turntable movement. You may need to replace it to fix the issue. We hope this solves your problem!
Was this helpful?
Thank you for voting!
Prev
1
Next
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
1. Unplug unit 2. Open door, remove two screws above the top trim piece, slide and remove trim. 3. Remove screw behind control board and top left corner, then release from position. 3b. Unplug all wire terminations and set control panel aside. 4. Remove two screws securing latch board, lift and rotate board
... Read moreout of position, remove three micro switches, xfer monitor switch actuator from lower pin in old board and insert in new. Install new door switches and reverse procedure to complete repair.
Note 1. Take care to located new latch board so holding tabs line up, pass through frame, and openings for door tangs line up with openings in frame before securing with screws.
Note 2. A long magnetic screwdriver is helpful.
Read less
Was this helpful?
Thank you for voting!
Had to replace charcoal filter
15 of 25 peoplefound this instruction helpful.
Jared from SIERRA VISTA, AZ
Easy
15 - 30 mins
Open the front cover by pushing it at the top (where it says “Push”), lifting up and pushing back on top edge of the old filter. Pull it out. Installing the new one is basically just the reverse of those steps! That simple.
Old filter did seem to be a little thicker (filter material), but the new one was the exact same dimen
... Read moresions, so it went in properly. Wish the filter material was white, so you knew just how dirty it was actually getting. But... :-D