The door strike on your washing machine allows your washer door to lock properly, and operate efficiently. If you notice that your washer door will not open or close, leaks or the washer will not star...
$19.58
In Stock
Order within the next 1 hr and 53 mins and your part ships today!
This kit is used for front load washers and includes 2 dual-stage shock absorbers, 1 spare shock mounting pin and 4 locking nuts. These shock absorbers keep the washer from vigorous shaking during it's cycles.
$50.58
In Stock
Order within the next 1 hr and 53 mins and your part ships today!
This door lock and switch assembly is manufactured to lock the door on your front load washer to prevent it from opening while it is running. You may need to replace the door lock and switch if the do...
$163.10
In Stock
Order within the next 1 hr and 53 mins and your part ships today!
The pump is what your washer uses to remove the water from the tub. This part is the pump and motor assembly which includes the red flapper to prevent drain back flow.
$211.11
In Stock
Order within the next 1 hr and 53 mins and your part ships today!
Also known as a Door Boot Seal and is used in front load washers. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately f...
$393.85
In Stock
Order within the next 1 hr and 53 mins and your part ships today!
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
$16.47
In Stock
Order within the next 1 hr and 53 mins and your part ships today!
Order within the next 1 hr and 53 mins and your part ships today!
Questions And Answers for ATF6000FS1
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Élise
December 9, 2019
J ai une laceuse frontal Frigidaire affinité et quand ma porte est fermer pour démarrer la laveuse elle m indique loc et clignote tout le temps.. je ne peux pas démarrer ma laveuse... que faire?
For model number ATF6000FS1
Bonjour Élise, Merci pour la question. C'est normalement une indication que le verrou de porte, numéro de pièce: PS12364048 devra être remplacé. J'espère que cela t'aides!
When washing the washer is shaking really hard. This just started in the last couple weeks. Can you please tell me what could cause this and it needs parts can you advise which ones and cost.
For model number ATF6000FS1
Hello Jo, thank you for your question. That issue is most likely caused by bad shock absorbers. We would recommend replacing those parts which are PartSelect Number: PS3508101. I hope this helps.
My washer does not start anymore and it displays a writing (pav) and (loc) what can i do
For model number ATF6000FS1
Hi Tommy, I would unplug the unit for an hour and plug it back in. If the issue persists you may have a faulty control board. Thank you for your question and good luck with your repair!
This was one of the simpliest repairs I have ever done taking less than 5 minutes to complete. On the inner door I removed the two screws that hold the plastic catch in place. I then removed the broken catch and put the new catch in place. Finally I replaced the two screws that hold the catch in place and it was done.
1. Unplug unit. 2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver. 3.Slide top back and remove. 4. Open door of washer and unscrew 2 screws holding in door lock unit. 5.Pull out unit from the top and install new unit reconnecting the 3 wire connections.
remove top of machine by removing 3 screws along the top edge in the back of your machine and then sliding the top back and up. Then loosen the screws holding on the control panel enough to get to the 2 screws at the top of the door panel. Next remove bottom panel by removing 2 screws along bottom edge then pulling it free from snaps. Then along the outside lip of the bellow, just inside the door, is a wire clip that is easily removed by prying it past rubber lip with a screw driver and lifting it away. Remove the door panel by removing the 2 screws you exposed by loosening the control panel and 2 more along the bottom that were exposed when removing bottom panel. After the door panel is removed and the bellow is completely exposed, you will find that it is held in place by a circular spring which wraps the whole way around the drum opening. Again it can be removed by prying it out away from the groove in which it sits with a screw driver. Now your machine is broken down as far as it needs to be. From here you can follow the directions included in your new bellow kit and put it back together by following these instructions in reverse.