This water filter purifies water going to the water dispenser and sometimes the icemaker as well. This part should be replaced if it is causing reduced water flow or just replaced periodically per the...
29% OFF
$49.99
$69.99
In Stock
Order within the next 1 hr and 6 mins and your part ships today!
This modular ice maker assembly replaces worn-out units to restore ice production in refrigerators. It includes the ice mold and control device but excludes the cover, ice level arm, wire harness, and...
$146.43
In Stock
Order within the next 1 hr and 6 mins and your part ships today!
This electronic control board is a critical component in refrigerator systems, responsible for regulating temperature settings and managing cooling and defrost cycles. If your appliance is experiencin...
$217.62
In Stock
Order within the next 1 hr and 6 mins and your part ships today!
The water inlet valve is a solenoid-operated switch that, when activated, releases water from the supply line to the water valve and into the compact icemaker mold and to the water line.
$208.88
In Stock
Order within the next 1 hr and 6 mins and your part ships today!
This includes both the run capacitor and the start relay. The capacitor helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer.
The start ...
$88.91
In Stock
Order within the next 1 hr and 6 mins and your part ships today!
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$28.95
In Stock
Order within the next 1 hr and 6 mins and your part ships today!
This light switch may also be known as a refrigerator door switch or a light switch kit, and is compatible with your refrigerator. The function of the refrigerator door switch is to turn on the light ...
$38.96
In Stock
Order within the next 1 hr and 6 mins and your part ships today!
This evaporator fan motor is located in the back of the freezer, and circulates air over the refrigerator coils. These coils will covert the heat into cool air, which is then circulated.
$79.52
In Stock
Order within the next 1 hr and 6 mins and your part ships today!
Questions And Answers for ASD2627KEW
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Linda
February 18, 2020
I need dimensions... width & height..
please.
For model number ASD2627KEW
Hello , Thank you for the question. Very sorry but we do not have the dimensions for this. You will need to make contact with the manufacturer directly. Thank you for your inquiry.
Was this helpful?
Thank you for voting!
Janice
July 22, 2023
I had my icemaker turned off for quite a while due to not having a new filter got filter replaced have water to my door and my icemaker does work. I filled manually with water and makes cubes, but there is no water going to icemaker.
For model number ASD2627KEW
Hello Janice, thank you for reaching out. The issue is most probably with the dual water inlet valve, part number PS11743697, but before replacing it, we would recommend checking the water lines for any clogging or leaking. We hope this helps, good luck with this repair!
Pressed in the end of the filter cover, lowered it down part way. Twisted the old filter 1/4 turn and removed it. Set in the sink to drain. Inserted new filter and twisted it to lock. closed cover. Done. Total time @ 1 Minute.
Interior surface of ice tray felt rough & flaky (coating deteriorated) so cubes would not release. Unplug appliance. Remove timer cover by hand pressure @ edge. Remove single attachment screw & bracket at lower front of icemaker. Disconnect wiring harness from socket @ rear of compartment. Tricky part was determining what type of connection held the other two attachment points along the long edge of the icemaker. I did not have repair manual or useful drawing but looked @ PartsDirect pic of side brackets & used a small mirror to confirm that mine were also some sort of "snap in" attachment. Remove icemaker unit by pushing upward and outward on the unit. I takes a good bit of pressure and will pop loose, but be careful not to break attachment bracket from freezer wall. Scavenge shut off bar and wiring harness from old icemaker once you have it out & attach to new one before installing it back in freezer. Again, you might find a mirror useful to align those pesky snap-in brackets with the new unit. Since you probably kept your freezer running while waiting for the part, the plastic snap-ins will be cold and brittle. I warmed them up first by applying a dampened cloth heated in the microwave to make them a little more pliable. A good push of the new unit towards the snap-ins along with some upward force will get it stable. Reattach the metal screw in bracket & connect the wiring harness to rear plug... and don't forget to plug the whole thing back in. It will take awhile for the first batch of cubes dump as the timer may need to cycle completely around to get to the fill cycle... be patient. Dump the first couple of batches of cubes just to make sure you're free of any residue.
unplugged refrigerator and shut off water, removed one screw and loosened two more, after removing one side of the ice bucket rail, unplugged electrical from old ice maker. Then I removed the bail and out on new one, reinstalled ice maker in reverse order from taking it out.
.gif "SUPPLEMENTAL INFORMATION Diagram and Parts List for Amana Refrigerator")
