This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are most often used to light the inside of refrigerators and ranges. It features a standard socket base, which means you simply unscrew the burnt-o...Read moreut bulb and screw in the replacement. Depending on the appliance you may require a screwdriver or nut driver to access the light bulb. We recommend you wear work gloves while handling this replacement part. It is constructed of glass and metal and is sold individually. Depending on the appliance and location of the bulb within it, you may want to consider disconnecting power and using a flashlight for easier access to unscrewing and re-screwing in your bulb during this repair.
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, and freezers. This is a genuine OEM part and includes a brush applicator. Please remember to wear gloves to protect your hands when applying this paint.
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.
This oven temperature sensor is designed to monitor and regulate the internal heat levels of your range, ensuring consistent and accurate cooking performance. It communicates directly with the control board to adjust heating as needed. Over time, exposure to high temperatures can cause the sensor to degrade, leading to uneven heating or f...Read moreailure to maintain set temperatures. If your oven struggles to reach or hold the correct temperature, replacing the sensor may resolve the issue. This OEM replacement part includes a wire harness for connection and is installed using two mounting screws. Installation is simple and typically requires only a screwdriver. Please note that the sensor is sold individually and does not include additional hardware.
The light socket on your electric range connects the power source to the light bulb. If your oven light is malfunctioning, you may need to replace the light socket. The light socket is located in the back of your range, so in order to access it you will need to remove the back panel. Many of our customers have rated this repair as easy, a...Read morend it should take less than 15 minutes. Before you begin this repair, make sure to disconnect the power source from your range. This is an OEM part sourced directly from the manufacturer.
This oven rack offers a sturdy, chrome-finished surface for baking, roasting, and broiling in your range. It fits a wide selection of compatible ovens and is built to handle high heat and frequent use. If your current rack is bent, rusted, or missing, this replacement restores safe and reliable cooking support. Be sure to check your oven model for compatibility. Sold separately.
This part helps your gas oven light properly. It creates the spark that ignites the burner and works with the safety valve to make sure everything runs safely. If your oven isn’t heating, only gets a little warm, or the igniter glows but doesn’t light the flame, this part might need replacing. It fits many Whirlpool, KitchenAid, and Mayta...Read moreg ranges and is built to last. Be sure to turn off the power and gas before installing.
Give your oven door a clean, finished look with this white side trim piece. It fits on the right edge of the door, helping seal in heat and protect the glass. If your current trim is cracked or loose, replacing it can improve both the look and performance of your oven. You’ll need to take the door apart a bit to install it, but it’s a solid fix for a worn-out part.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Lori - For model number AGR6303MFS0
November 25, 2019
Need stove top knobs for the burners ones that are not so cheaply made that they melt what is the parttys number for the knobs or valves
Hello Lori, thank you for inquiring. For your model, the Knobs are part number PS12114313 for black, part number PS11768805 for white, and part number PS12347974 for stainless. They are all sold individually. Good luck with your repair!
5 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
GEORGE - For model number AGR6303MFS0
August 13, 2021
Wondering if my oven prob is as mentioned here? I tested the temp sensor and it read 1080 ohms the gas valve test 216 ohms at each terminal coil. Replaced the spark module board and the oven bake and broil now comes on then shuts off after bout a minute or 2. The Flame is a dark deep blue so dont think its a weak igniter it uses a spark igniter electrode in oven. Any advice would be appreciated can a sensor probe test 1080 ohm but still be defective mechanically?
Hello George, Thank you for your inquiry. We would recommend checking the bake and broil igniters as well as the gas valve. The sensor should test between 1080 and 1090 and it should be good if it does. Hope this helps.
Was this helpful?
Thank you for voting!
Jack - For model number AGR6303MFS0
April 14, 2023
how to replace oven lite
Hello Jack, thank you for contacting us. To change the oven light, follow the following steps:
1. Unplug the range or disconnect the power.
2. Turn the glass bulb cover in the back of the oven counterclockwise to remove it.
3. Turn the bulb counterclockwise to remove it from the socket.
4. Replace the bulb, then the bulb cover by turning clockwise.
5. Plug in the range or reconnect the power.
We hope this helps, good luck with this repair!
Was this helpful?
Thank you for voting!
Tania - For model number AGR6303MFS0
May 2, 2024
I need the gas regulator for a whirlpool stove. The part # is: 16501002-2 and the series # is: R64116059. Thanks
Hi Tania, thank you for your inquiry. The pressure regulator you are looking for is part number PS11756682. Please reach out to customer service if you need help placing an order, anyone will be happy to assist you!
Can the flames be lowered? The flames are so high it burns the food before it is cooked.
Hi Carmela, thank you for reaching out. We would suggest checking the spark ignition switch and harness, part number PS12584280. You may need to replace it to fix the issue. We hope this solves your problem!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
mice had made nests in the insulation wrap in the range
129 of 211 peoplefound this instruction helpful.
Wendy from Red Hook, NY
Easy
More than 2 hours
Screw drivers
I numbered every part. ex: 1 L., for first part removed left side. I used a magic marker to circle the holes and wrote the number of screws used on the part, set the srews in a separete place, so that I new where these screws went to. The cleanup was pretty time consuming, but I was able to keep my stove, when every repairman I called to
... Read more fix my stove told me I was better off buying a new stove. ($600.00 stove 2 years old)Please Note: The insulation blanket needed for the entire stove is two pieces, the sides and top are one part # and the bottom and back, are another part #. I did not know this. I just purchased the top and sides. I got lucky, the back and bottom were still in good shape. So I guess I should have read the description of the part more carefully to see what it covers, before I ordered it. It took two people two hours to do the work, it was really nice to have an extra set of eyes, to remember what direction pieces of metal from the stove went. I would do it all over in a heart beat instead of buying a new stove.
Read less
Was this helpful?
Thank you for voting!
Bake/broil would not work
83 of 133 peoplefound this instruction helpful.
Greg from North Baltimore, OH
Really Easy
15 - 30 mins
Screw drivers, Wrench (Adjustable)
Replaced igniter and also DSI/direct spark igniter did not fix problem. Called out repairman turned out to be bad gas valve. Replaced that part , now stove works fine.
Was this helpful?
Thank you for voting!
Socket Light had a bad thread
44 of 66 peoplefound this instruction helpful.
Edmund from Emporium, PA
Easy
15 - 30 mins
Pliers, Screw drivers
Socket Lite come with clips attached to the outside of the housing. After you unhook the 3 lead wires that are attached to the unit. All you have to do is push in on the clips and release the unit. Then you snap in the new unit. Attach the 3 wire leads, put a oven bulb in the socket end, and the install the light cove
... Read morer
My Orders
