This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are mos...
This can be used for either the bake igniter or broil igniter in your appliance. NOTE: The part may differ in appearance but will function the same as the original.
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
This is a replacement screw and washer for your oven/range. It is a Phillips-head screw approximately half an inch long, and the washer is approximately 1 inch in diameter. The screw attaches the oven...
This door hinge can be used for the left or right side. As per the manufacturer if the hinges have never been replaced on the appliance, they suggest to replace the door hinge receptacle kit.
$79.05
In Stock
Questions And Answers for AGR5735QDB
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Bill
February 20, 2023
Or window is filthy inside the two windows can this be fixed
For model number AGR5735QDB
Hi Bill, thank you for contacting us. Firstly, we recommend cleaning the window from both inside and outside. For this, apply a drop of grease-cutting dish soap to a damp cloth. Work the dish soap into the sticky spots until they are gone. Rinse with a damp cloth and dry. If the window is still filthy, you will need to disassemble the door and clean the inside of the glass panes, and then assemble it again. We have included a relevant video to assist you in disassembling the door assembly. We hope this sorts out your problem!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
My oven has two igniters so I needed to determine which one was the problem.
Using the amp/multi meter I tested the connection between the igniters and the valve, with the oven turned on, to find the bad igniter. Depending on the model of stove you have, the amp reading you need for a properly functioning igniter will vary. My lower igniter read 2.7 amps with a rated amp between 3.3 and 3.6. So that was the culprit.
Replacing the igniter was easy. Two screws and a wire connected with a plug. I was able to do the diagnosis and unplug the wire without pulling the oven out. I pulled the drawer out and removed the two screws in a cover behind where the drawer was. You may not be so lucky…I have long arms.
I found removing the oven door made it easier to reach the igniter itself. To remove the door just open it slightly and pull up, it should come off easy…and replace in opposite manner.
Keep track of your screws and put it back together the way you found it except for the igniter that is.
Anyone with moderate technical skill could easily do this repair. The diagnosis is the hard part. I estimate I saved about $200 doing it myself.
Repair tech checked oven and said the control panel was bad and needed to be replaced. The new control panel would cost over $450.00! I found that the oven sensor was bad and replaced it for $30.00. The old oven sensor had failed following a self cleaning cycle. I found that the wires coming out of it were burnt.
Replacing the oven sensor was very easy. I removed the back panels 6 screws to gain access to the sensor's connection. I then removed the 2 screw that hold the sensor in place inside the oven and pulled the old sensor out through the oven. I reversed this process to place the new sensor in the oven.
I removed the oven door, unscrewed a couple of screws, replaced the ignitor, put screws back in, done! Sometimes it would take my oven up to an hour to heat up and sometimes it just wouldn't heat up, just fill the house with a gas smell. Now, it heats up in about 3 minutes!! We were considering buying a new oven, we will just keep this one. $40.00 beats $700.00