This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
$10.20
In Stock
Order within the next 8 hrs and your part ships today!
This evaporator fan motor is located in the back of the freezer, and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated.
NOTE: ...
$94.55
In Stock
Order within the next 8 hrs and your part ships today!
This is a replacement crisper drawer for your refrigerator. The drawer is approximately 24 inches long, 11 inches wide, and 12 inches tall. It is made of clear plastic and is sold individually. The cr...
$136.15
In Stock
Order within the next 8 hrs and your part ships today!
Order within the next 8 hrs and your part ships today!
Questions And Answers for A9RXNMFWB02
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Dan
April 4, 2024
How do I unplug the defroster line? How do I push in the tabs to drop the plastic housing that covers the defroster funnel?
For model number A9RXNMFWB02
Hello Dan, thank you for getting in touch. We have attached a relevant video that will help you in removing the defrost timer. The video may not be of the same exact model but will help you with the process. We hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
I knew the chances of all the freon leaking out was unlikely so I looked at the wiring to the compressor and there was a capacitor and a starter/overload so i figured I would start there. I went on line and found the parts at this site and they were less than the minimum service call charge for a service tech so I figured what the heck let's give her a shot so I did give it a shot. I ordered the parts and they were there in less time than a service tech could come out and i installed the parts and guess what for 90.00 in parts and 15 minutes in time I repaired my refrigerator. Thanks guys, It took less time to order the parts than it did to make the repair so thanks, your website rocks and is very well designed so my hat is off to you guys!
First I removed the two screws that secure the guard in bottom back of the freezer and removed it . Next I removed the two screws that secure the guard on the back wall of the freezer and removed it. There are three wires connected to the motor, I unplugged those and removed the two screws that secure the motor and removed it. I swapped the grommets, blade and support bracket from the old motor. I put it back together in reverse steps and its working great. My mother-in-law can,t stop thanking me ! I saved her at least $400 to buy a new fridge. Thank You, Brian Miner
My refrigerator is approximately seven years old (date of manufacture: 2001). I had come home twice in the last month to find that it had not been running for several hours (ice melted, milk spoiled, etc.) but it would start running again if I twisted the thermostat knob. So, I ordered a new thermostat. First I removed the 1/4" hex screw that held the plastic thermostat housing in place (it screws up into the top of the refrigerator compartment). Then I removed the plastic thermostat knob and slid the old thermostat out of the housing. I then disconnected the wires one-by-one from the old thermostat and connected them to the new one so I could be certain they were all connected correctly. Finally, I pulled the plastic sheathing off the old sensor wire, slid it onto the new one and popped the wire back into place. Slide the thermostat back into the housing, screw the housing back into the top of the refrigerator compartment, replace the plastic thermostat knob, and the job is done.