9503BHKIT Makita Grinder - Overview

This manufacturer sourced replacement pin is made out rubber and it is sold individually. It acts as a cushion/spacer in a variety of Makita power tools. This is a standard piece of hardware and it has multiple applications based on your tool. Please refer to diagrams for correct application.

Length 8 Foot Length: 6' Gauge: 18 Wires: 2 Type: Bare Wire This power supply cord is a genuine OEM sourced replacement part. It is specially made to supply power from a standard outlet to Makita power tools. A cracked or damaged cord should be replaced before continuing to use the tool. This rubber insulated cord is sold individ...Read moreually. It comes with a rubber sleeve grommet that is not sold separately. Replacing this power supply cord you will need a screwdriver. • Remove the housing screws • Remove the the housing • Disconnect the old cord wires • Remove the old power cord • Secure the new cord in place • Connect the wires • Reassemble and test the new cord

This genuine manufacturer-sourced part is specially designed for Makita power tools. It is an important component which provides a tight seal between connected components. Unfortunately, over time it will wear out and it may begin to crack eventually requiring a replacement. To ensure the correct repair procedure, refer to the appropriate...Read more diagrams for your model. Note, this high-quality insulation washer is made of durable material and is sold as an individual item. A screwdriver will be needed to take apart and reassemble the tool when performing this repair.

This is a Ball Bearing that is sealed on both sides. This is a genuine Makita replacement part that is sold individually. • Ball bearings minimize friction between 2 parts in your tool that would otherwise spin and rub against each other. The balls or rollers take the load and spin, distributing the weight evenly while the minimal co...Read morentact area of the balls reduce friction. This reduces wear on the tool and allows it to run smoothly. • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

This Ball Bearing is sealed on both sides. This is a genuine Makita replacement part that is sold individually. • Ball bearings minimize friction between 2 parts in your tool that would otherwise spin and rub against each other. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area...Read more of the balls reduce friction. This reduces wear on the tool and allows it to run smoothly. • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

This cord guard is a genuine Makita replacement part, and it is a direct replacement for a damaged or missing cord guard. Power tool cords undergo a lot of stress, and these cord guards help to alleviate some of that stress at the weakest point--right where the cord enters the tool. Over time cord guards will deteriorate and eventually re...Read morequire replacement. Keeping a strong cord guard on your tool will help will cord life. This cord guard is compatible with the tools listed below, but it is not guaranteed to fit any other power tools.

This authentic OEM sourced part which is specially made for use with Makita power tools. It is important to have a cord protector on your tool to improve friction, seal cable and protect it from a potential damage. The part provides an identical replacement for a missing or a faulty component that was installed on a new unit. Please make ...Read moresure to refer to the appropriate diagrams of your model for the correct location and application of this part. Keep in mind this high-quality strain relief is made of durable rubber and is sold individually.

This replacement screw is a high-quality hardware that is specially designed for use with Makita power tools. It has multiple applications depending on the model of your equipment, please make sure to check the appropriate diagrams for the correct location and use of this item. Keep in mind this high-quality item is made of durable metal and is sold individually.

It is a genuine OEM sourced replacement screw which is specially designed for use with Makita power tools. This screw is a standard hardware which has multiple applications depending on the model of your unit, please make sure to check appropriate diagrams for the correct location and use of this item. This high-quality pan head screw is made of durable metal and it is sold individually.

This is a genuine OEM sourced part which is specially designed for use with Makita power tools. It is a standard hardware which may have multiple applications. Please make sure to refer to the owners manual and the appropriate diagrams of your model for the correct location and application of this component. Keep in mind this high-quality screw is made of durable metal and is sold individually.

Genuine Makita replacement part. This pan-head phillips screw includes a washer. It is sold individually.