My Orders
919-72427 (Type 1) Craftsman Compressor - Overview
Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".
Search filter:
Clear Filter
Your search term must have 3 or more characters.
No Longer Available
Kit
Part #K-0648
No Longer Available
Eccentric
Part #D24597
No Longer Available
Muffler, Intake
Part #ACG-11
No Longer Available
Label
Part #LA-3105
No Longer Available
Piston, Rod Cylinder Kit
Part #A02743
This is an original OEM part. The connecting rod kit is constructed of metal and rubber parts. The piston and the crankshaft are fastened together by the connecting rod kit within the pump. It is recommended to refer to the specific manual and diagrams for repair instructions. This part is sold individually. A hex key and a wrench are necessary in the removal and replacement.
No Longer Available
Relief
Part #SSW-7482
No Longer Available
Intake Muffl
Part #AC-0783
$12.20
Special Order
DRAIN VALVE
Part #N286039
When using an air compressor, moisture naturally builds up inside the tank as air is compressed. If this water isn’t drained regularly, it can lead to internal rust and damage over time. That’s where the drain valve comes in—it allows you to release the built-up water and keep your tank in good condition. Located at the bottom of the tank...Read more, this valve should be opened after each use to prevent corrosion and extend the life of your compressor. If you tend to leave air in the tank for long periods, water accumulation can be even more significant. This replacement drain valve features a thread size of 18 TPI and is sold individually. Regular maintenance with a working drain valve helps ensure safe and efficient compressor operation.
Read less
$7.44
Special Order
ISOLATOR 3 POINT MOU
Part #ACG-19
$104.71
In Stock
ASSY VALVE PLATE
Part #Z-AC-0032
This replacement valve plate assembly is a high quality item designed for use on Craftsman air compressors. It is a genuine manufacturer sourced item that is used to control the airflow into the cylinder. Once the piston starts traveling up, the reeds on the valve plate open and air is sent into the air tank. Overtime the reeds will get w...Read moreorn eventually requiring valve plate replacement. One metal valve plate with reed valves and two rubber seals are included in this assembly. When replacing this valve plate assembly it is also a good time to replace the head gaskets which are sold separately. You will need a wrench set to complete this repair.
Read less
$7.44
Special Order
ASSY FASTENER
Part #ACG-408
This assembly fastener is supplied directly from the original equipment manufacturer. The screws are constructed of metal, and are compatible with many compressor machines. This part is often used to secure the compressor shroud. It is recommended to refer to specific manual and diagrams for repair instructions. This part is sold individu...Read moreally. Purchasing spare screws is also encouraged, as they can wear out over time and regular use. A hex key and a screwdriver are helpful in the removal and replacement.
Read less
$7.44
In Stock
ORING P/L HEAD
Part #ACG-45
O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. rnrnThere are many causes for O-Ring failure. The most common among power tools are: • Extrusion and Nibbling - The O-ring has ragged, tattered edges. ...Read moreThese are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that it too rough, contains grit or is too smooth to allow lubrication. • Over Compression - The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening - The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking - The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.
Read less
Common Symptoms of the 919-72427
How this model fails, and the parts that fix it.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!
View More