919-72413 (Type 1) Black and Decker Compressor - Overview

This is a genuine item that is supplied by the original equipment manufacturer for use with air compressors and pressure washers. It is an identical replacement for a missing or faulty wheel that was originally installed on a new unit, please make sure to refer to the appropriate diagrams of your model for the correct location and applica...Read moretion of this component. Keep in mind this high-quality item is made of durable materials and is sold individually. Note that the hardware to secure it is sold separately.

This is a genuine Craftsman replacement part that has been sourced from the original manufacturer to be used with air compressors. The carbon brushes are used to relay electricity from the switch to the motor's armature. These brushes are priced and sold as a pair because two brushes are required.

This genuine OEM replacement kit is designed for use with select air compressors and includes essential components to restore proper function. The kit comes with a piston rod, compression ring, cylinder sleeve, and bearing—ideal for repairing worn or damaged internal parts. Please note that this kit does not include the valve plate, head ...Read moregaskets, or any other compressor components, so be sure to check your model’s requirements before beginning repairs. Installation requires basic tools: a screwdriver, hex key Allen wrench), and pliers. With these tools and a bit of care, you can perform a straightforward repair that helps extend the life and efficiency of your compressor.

Genuine Porter Cable replacement part Includes 2 Carbon Brushes with wire lead attached and installation instructions. • Worn brushes are frequently the cause of a poorly running motor. • Replacing brushes can fix an intermittently operating motor. • New brushes can restore a motor's electric braking. Carbon motor brushes are...Read more one of the most commonly replaced power tool parts. The reason is that carbon brushes are wear items, meaning that through friction and use they will gradually wear away and eventually will need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, also check your armature for burns, cracks, or other damage which are indications of a larger motor problem needing attention.

This safety valve is a genuine replacement part manufactured for use with air compressors. If the compressor's pressure switch malfunctions, and does not turn the motor off when the amount of pressure is met, the safety valve will open to release the extra air pressure. The amount of pressure required to open the safety valve is set by te...Read morension of the spring inside the valve. The spring can wear out, and leave the valve open at a lower pressure than what is set to turn the switch off, and will not allow pressure to build inside the tank. This safety valve has a thread sealant pre-applied, so additional thread sealant is not required, the safety valve is sold individually.

When using an air compressor, moisture naturally builds up inside the tank as air is compressed. If this water isn’t drained regularly, it can lead to internal rust and damage over time. That’s where the drain valve comes in—it allows you to release the built-up water and keep your tank in good condition. Located at the bottom of the tank...Read more, this valve should be opened after each use to prevent corrosion and extend the life of your compressor. If you tend to leave air in the tank for long periods, water accumulation can be even more significant. This replacement drain valve features a thread size of 18 TPI and is sold individually. Regular maintenance with a working drain valve helps ensure safe and efficient compressor operation.

This is an OEM part sourced directly from the manufacturer. The belt is commonly found in Craftsman air compressors. This part is made of flexible rubber, and is used to transfer power between the piston and the pump assembly. Over time, it may become cracked and brittle, requiring replacement. You may need an Allen wrench or hex key when replacing this part. This item is sold individually.

This is an OEM part sourced directly from the manufacturer. The adapter is designed for use in compressors from DeVilbiss, Black & Decker, Delta, and Porter Cable. This part is made of metal, and may be used to connect the regulator to the tank. You will require a wrench when replacing this part. This item is sold individually.