919-16538 (Type 2) Black and Decker Compressor - Overview

This is a genuine replacement part sourced from the original manufacturer for use with horse power compressors made by Black and Decker. This pump activates the air compressor pump to turn on and off, which helps regulate the air pressure. It is recommended to review your models diagram to verify the parts compatibility. This part includ...Read morees the micro press switch, a screw and a clamp. This micro press switch is made of durable material.

This genuine OEM replacement kit is designed for use with select air compressors and includes essential components to restore proper function. The kit comes with a piston rod, compression ring, cylinder sleeve, and bearing—ideal for repairing worn or damaged internal parts. Please note that this kit does not include the valve plate, head ...Read moregaskets, or any other compressor components, so be sure to check your model’s requirements before beginning repairs. Installation requires basic tools: a screwdriver, hex key Allen wrench), and pliers. With these tools and a bit of care, you can perform a straightforward repair that helps extend the life and efficiency of your compressor.

Genuine Porter Cable replacement part Includes 2 Carbon Brushes with wire lead attached and installation instructions. • Worn brushes are frequently the cause of a poorly running motor. • Replacing brushes can fix an intermittently operating motor. • New brushes can restore a motor's electric braking. Carbon motor brushes are...Read more one of the most commonly replaced power tool parts. The reason is that carbon brushes are wear items, meaning that through friction and use they will gradually wear away and eventually will need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, also check your armature for burns, cracks, or other damage which are indications of a larger motor problem needing attention.

This safety valve is a genuine replacement part manufactured for use with air compressors. If the compressor's pressure switch malfunctions, and does not turn the motor off when the amount of pressure is met, the safety valve will open to release the extra air pressure. The amount of pressure required to open the safety valve is set by te...Read morension of the spring inside the valve. The spring can wear out, and leave the valve open at a lower pressure than what is set to turn the switch off, and will not allow pressure to build inside the tank. This safety valve has a thread sealant pre-applied, so additional thread sealant is not required, the safety valve is sold individually.

When using an air compressor, moisture naturally builds up inside the tank as air is compressed. If this water isn’t drained regularly, it can lead to internal rust and damage over time. That’s where the drain valve comes in—it allows you to release the built-up water and keep your tank in good condition. Located at the bottom of the tank...Read more, this valve should be opened after each use to prevent corrosion and extend the life of your compressor. If you tend to leave air in the tank for long periods, water accumulation can be even more significant. This replacement drain valve features a thread size of 18 TPI and is sold individually. Regular maintenance with a working drain valve helps ensure safe and efficient compressor operation.

This is an OEM part sourced directly from the manufacturer. The belt is commonly found in Craftsman air compressors. This part is made of flexible rubber, and is used to transfer power between the piston and the pump assembly. Over time, it may become cracked and brittle, requiring replacement. You may need an Allen wrench or hex key when replacing this part. This item is sold individually.

This is an OEM replacement part used on Air Compressors. The gauge registers pressure readings and allows you to maintain needed pressure. This Gauge is Sold Individually. You would need a Wrench to secure this Gauge to the Manifold. When replacing this item make sure to unplug the air compressor and bleed out air from the tank.

It is a genuine item that is supplied by the original equipment manufacturer for use with DeWALT, Black and Decker and Porter Cable Compressors. This is a special hose that the air would flow through. It provides an identical replacement for a missing or a faulty component that was included with a new unit. Please make sure to refer to th...Read moree appropriate diagrams of your model for the correct location and application of this part. Keep in mind this high-quality air hose is made of durable rubber and is sold individually.

This replacement hose clamp is designed for use in various compressor models and serves an important role in securing hoses to specific parts of the unit. Whether you're performing maintenance or replacing worn components, this clamp helps ensure a tight, leak-free connection. Made from durable metal and sold individually, it’s easy to in...Read morestall and built to withstand the pressure and vibration common in compressor operation. If your hose feels loose or you're noticing air leaks, replacing the clamp can help restore proper function and keep your compressor running smoothly.