91142719100 Kenmore Cooktop - Overview

Diagrams for 91142719100

See every part. Know exactly what you need.

Parts for the 91142719100

$198.87

Dual Radiant Element - 9 Inch

★★★★★

(2)

Part #WB30T10099

This is a large dual haliant element with a limiter or sensor for glass cooktops and freestanding ranges. It is a 2500-watt part. The inner diameter measures 9 inches, while the outer diameter measures 10 inches. If there is no heat generated from your element, you may need to replace this part. You may also need to check your socket or i...Read more

Read less

$202.38

Infinite Control Switch

★★★★★

(1)

Part #WB24T10119

Large Haliant Burner with Limiter - 8"

★★★★★

(2)

Part #WB30T10045

This haliant burner element is a gneuine OEM replacement part for your stove. This element is 8 inches in diameter. The element lies underneath the stovetop, and will need to be replaced if it stops heating. To complete this repair you will need a 1/4 inch nut driver and a flat blade screwdriver. To access the element, open the oven door and unscrew the two screws under the lip of the cooktop.

6" Heating Element

★★★★★

(1)

Part #WB30X44826

This 6-inch radiant surface heating element is a genuine OEM component designed for use with select electric ranges and cooktops. Also known as a haliant element it delivers 1500 watts of consistent heat from beneath the glass or ceramic cooktop surface ensuring efficient and even cooking performance. The element is engineered to glow vis...Read more

Read less

$192.75

Tape

★★★★★

(1)

Part #WB06T10007

This roll contains 108 inches of tape.

$13.95

Screw

Part #WH2X930

This screw is sold individually.

$43.07

Range Indicator Light

Part #WB25T10012

$300.89

Haliant Element - 1200W

Part #WB30T10043

KNOB INF (BLACK)

Part #WB03T10020

KNOB INF White

Part #WB03T10021

$37.95

ELEMENT SUPT BRACKET

Part #WB02T10090

INDICATOR LIGHT

Part #WB25T10017

Common Symptoms of the 91142719100

How this model fails, and the parts that fix it.

Element will not heat

Fixed by
these parts

Show All

Repair Tips From Fixers Like You

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Large burner on dual element burned out

102 of 116 people found this instruction helpful.

Scot from Oakland, FL
Easy
15 - 30 mins
Pliers, Screw drivers, Wrench (Adjustable)

This was really easy, and pretty with no problems or issues It took me longer to write this than to do the actual installation. I used a digital camera to help me remember where things were, but a pen/paper works fine. Here's what I did:

1. Turn off the breaker for the cooktop.

2. Remove (2) 1/4" hex screws directly ... Read more under cooktop. You may need to open oven door to reveal them.

2. Prop up cooktop. I used the box the replacement element came in.

3. The element is held in place with (3) brackets held in by a #2 philips screw each. Mark the location of each of the brackets. There are numbers on the element to help you do this.

4. Write down where each of the wires connects to the element. There's only a few of them, but I tend to forget that stuff. The wires have female spade-type connectors that connect to the male ends on the element.

5. Using a needle-nose or small pliers wiggle each wire off the element. Grab the wires by the end of the female connector when you do this. I found it helpful to use a small flat screwdriver to help pry them off. Mine were on pretty tight, so expect this to take a few mins. If you have problems getting to the wires, remove the brackets (next step) first and come back to this one. I let the element hang from the wires without any problems, but I still wouldn't recommend it.

6. Remove each of the screws with a #2 philips screwdriver. Support the element with your hand and gently pull each bracket away from the element. Once they're all gone, the element should just come out. I took a look at my old element and saw that the large burner wires were melted in a couple places, so it was definitely broken.

7. If necessary, clean the underside of the cooktop surface with a clean papertowel. There was a little dust from the old element on mine.

8. Connect the new element and test to make sure it works by turning on the breaker and turning on the burner for a second or two. Note: This will make the top of the element hot for some time, so test it and go away for a few mins. If it works OK, proceed. If not, disconnect and figure out what else may be wrong.

9. Using the old element, make copies of the marks you made for the bracket locations onto the new element. You'll have to punch through the insulation when re-attaching the screws.

10. Re-wire the new element, if necessary and re-attach the brackets over the marks you made. This may be a pretty tight fit because the new element was thicker than the old on mine. I opened up the brackets a bit to make it not so hard to re-attach. Hook the brackets on and squeeze them over the element. The holes in the brackets need to line up with the holes drilled into the bottom of the element. If they don't, spin the element around (or detach and re-attach the brackets) till they do.

11. Screw in the (3) screws over the brackets pushing them through the insulation on the element.

12. Close the cooktop and reattach the hex screws under it (1/4" hex).

13. Turn on the breaker and test again.

Thats it, works great now. Good Luck

Read less

Was this helpful?

Large burner would not get hot

70 of 95 people found this instruction helpful.

Kevin from Leominster, MA
Easy
Less than 15 mins
Nutdriver, Screw drivers

Repair was very simple. Removed 2 screws under the cooktop, tilt the cooktop back, unplug 4 wires from 8" burner, remove two screws holding retaining clips, install new burner in reverse order. Very simple!

Was this helpful?

Coil Burned Out

63 of 94 people found this instruction helpful.

Frank from St Augustine, FL
Really Easy
15 - 30 mins
Screw drivers

Open lid,un screw coil,pop in new coil snap holders in place,then cook a steak

Was this helpful?