892DT (Type 1) Porter Cable Router - Overview

This is a genuine replacement part manufactured for use is power tools. This versatile steel washer has many applications. Usually this type of washer is used when fastening two components of a tool together with a nut and bolt. This washer is sold individually, please see model diagram for part location and usage.

O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure, such as pressure, friction, temperature or chemicals. The most common are: • Extrusion and Nibbling ...Read more - O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. • Over Compression - O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening - O-ring has a pitted or cracked surface, and often is flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking - O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching causes similar cracking.

This is a genuine item that is supplied directly from the original equipment manufacturer for use with Porter Cable and Black and Decker power tools. It is a standard hardware which has multiple applications, please make sure to check the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality item is made of durable metal and is sold individually.

This handle is supplied directly from original equipment manufacturer. It is specially made for use with routers. Its purpose is to provide user with a solid grip of a tool for safe operation. This handle is made out of plastic material and it is sold individually. Please note, the screw that is used to secure this handle is sold separate...Read morely. This is a simple repair that should only require a hex key/allen wrench. • Make sure the unit is unplugged • Remove the handle screw • Replace old handle with a new one • Secure the handle screw

This wear plate is an original part from Porter Cable. Compatible with many routers, this metal plate is fitted onto the base housing, securing the shaft. Sold individually, a wrench and pliers are needed for the replacement.

The shaft attaches to the wear plate and the base housing. This part is made of metal and is available individually. It is a genuine replacement part sourced from the original manufacturer for use with engines and routers made by Porter Cable and Black & Decker. When replacing this item a set of pliers might be required during the installation process. It will require replacing if it becomes broken.

An authentic manufacturer-sourced washer which is specially produced for use with power tools. This replacement washer has multiple applications depending on the model of your unit, please make sure to check appropriate diagrams for the correct location and use of this hardware. It is a high-quality item which is made of durable metal and it is sold individually.

A genuine replacement part that is supplied directly from the original equipment manufacturer for use with Porter Cable and Black and Decker power tools. It is a special pin which helps to secure the components together, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this ha...Read morerdware. Keep in mind this high-quality item is made of durable metal and is sold individually.

This is a Genuine OEM replacement Compression Spring used on Laminate Trimmers/Routers. This part is made out of Metal and it is sold individually. This springs is attached with Spindle Lock Pin to the Housing.

Genuine Porter Cable replacement part, it is sold individually. The most poplar use of the 688860 Screw is to secure the base of the Router shown below. It is a flat head phillips screw. It is also used in various places of Plate Joiners and some of the Laminate Trimmers.

It is a genuine manufacturer-sourced replacement component which is specially designed for use with Porter Cable and Black and Decker power tools. This is a standard hardware which has multiple applications depending on the model of your unit, please make sure to check appropriate diagrams for the correct location and use of this part. Ov...Read moreer time the threads may wear out no longer providing a tight fit and eventually the screw will need to be replaced. Please note this high-quality metal hex socket screw is sold individually.

This item has been sourced from the original manufacturer to be used with routers from Porter Cable and Black & Decker. The lever is part of the base housing assembly. The lever is used to actuate the depth adjustment knob and ring. This item is priced as an individual replacement part.