80802 (AW1ESEA) LG Wall Oven - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Charcoal Filter – Part Number: 5230W1A003A
$50.55
In Stock
Air Duct Bracket – Part Number: 4810W1A151A
$24.15
In Stock
Air Duct Bracket
★★★★★
★★★★★
(1)
Part #4810W1A151A
This bracket holds the metal or plastic flapper that closes off the exhaust duct when the fan is not running and opens when the fan turns on. If the exhaust fan on your microwave does not appear to be working, the problem may be with the damper assembly. If the damper does not open and close easily, check for any damage to the bracket, and replace if it is damaged or faulty. This genuine OEM exhaust damper measures approximately 12 inches long by 5 inches wide.
Time Delay Fuse – Part Number: 3B74133Q
$13.15
In Stock
Spring – Part Number: 4970WRA001G
$13.15
In Stock
Spring
★★★★★
★★★★★
(1)
Part #4970WRA001G
This spring provides tension or controlled movement within the appliance mechanism. Engineered for durability, it supports smooth operation and helps maintain proper alignment of connected components.
Rivet – Part Number: 4051W3A001A
$11.95
In Stock
Rivet
Part #4051W3A001A
Hardware Mounting Kit – Part Number: 3861W1A043C
$48.35
In Stock
Hardware Mounting Kit
Part #3861W1A043C
Magnetron – Part Number: 6324W1A001L
$120.07
In Stock
Magnetron
Part #6324W1A001L
Thermostat – Part Number: 6930W1A003J
$16.45
In Stock
Thermostat
Part #6930W1A003J
Locker – Part Number: 4026W2A015A
$13.15
Special Order
Locker
Part #4026W2A015A
High Voltage Diode – Part Number: 6021W3B001V
$21.95
In Stock
High Voltage Diode
Part #6021W3B001V
Microwave Cover lamp – Part Number: 3550W1A171A
$16.45
In Stock
Microwave Cover lamp
Part #3550W1A171A
Screw,Taptite – Part Number: 1SBF0402418
$13.15
Special Order
Screw,Taptite
Part #1SBF0402418

Exact Part matches for your search term

STOPPER               *REPLACE – Part Number: 80802
No Longer Available
STOPPER *REPLACE
This part number matches the current model number 80802
Part #80802

Common Symptoms of the 80802

How this model fails, and the parts that fix it.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Magnitron failed
8 of 13 people found this instruction helpful.
  • Joseph from WILTON, NH
  • A Bit Difficult
  • 1- 2 hours
  • Screw drivers
Over the stove microwave installed in top cabinet row.
1. Unplug device.
2. Two people to remove from wall/cabinet (remove two, large, top mounting screws and rotate entire microwave down and off the wall mount). Should be some wood spacers between top of device and bottom of cabinet.
3. Remove screws from sheet metal cover .
4. Remove one screw holding blowers in place and rotate out of the way, in order to gain access to 2 of 5 screws that hold the magnetron in place.
5. Unplug magnetron and remove the 5 screws.
6. Drop in new magnetron and re-assemble microwave in reverse order (steps 5-3).
7. Two people restore micro to wall/cabinet. Replace wood spacers, re-install two, large mounting screws (finger-tight). Test device. Secure the two large screws.
Was this helpful?
Thank you for voting!
Would not heat and made a buzzing or popping sound
4 of 7 people found this instruction helpful.
  • Thomas from NEWARK, DE
  • Easy
  • 15 - 30 mins
  • Screw drivers
Unplug the microwave. Remove the Philips head and safety Torx head screws along the bottom of the sides and rear of the microwave which hold the black cover on. Lift the cover up at the rear and slide it backwards to disengage the tabs on the front top. Remove the cover. Discharge the capacitor by shorting the terminals to each other and then ground. Do this with a well insulated object and be aware there may be a pop when you do this. Keep hands, etc. on the insulated part of the object (screwdriver handle, etc). There's a lot of stored energy in that capacitor. I'd advise first checking the diode to make sure its not bad. Replace it if it is. The Magnatron is held in with a couple of screws on the top and sides. Unplug the connector and remove the screws. Remove the Magnatron. Installation is the reverse of removal.
Was this helpful?
Thank you for voting!
bad filter
3 of 5 people found this instruction helpful.
  • John from NORMANGEE, TX
  • Really Easy
  • Less than 15 mins
I took the cover off and just put the new charcoal filter in
Was this helpful?
Thank you for voting!