7MWFC9822HC0 Whirlpool Washer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Parts Used:
-
Howard from Boynton Beach, FL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
22 of 51 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
It took two of us to hold the ring and slide it on around the opening with the assistance of screwdrivers the spring was very tight
Two people to screwdrivers, stretching the spring out and around and that’s the last part to go on
Parts Used:
-
Terry from JUPITER, FL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Displayed “Door Loc” which was not correct error message
Replaced door latch after removing rubber seal from tub to access door latch. Simple replacement but did not correct issue. Notified service technician to determine error codes and had to replaced display panel and control module.
Parts Used:
-
John from SHERIDAN, WY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replaced the front bellow seal
i had no clue, yet when you you tube it, there are a few ones that are pretty good. Be patient, follow the directions, do not cut any corners or it will leak! The hardest part is putting the front clamp back on, here's how you do it;
put the wire clamp on at the top, and pull it around on the left side, then, by using the needle nose pliers, have the wire clamp at about 3:00 o clock on the right, there is a spring on that wire clamp, put that at 3:00 o clock as well, pull down as hard as you can at the spring which stretches the clamp, then work it around with your other hand, or your wife if she isn't scared like mine was
Best of luck,
put the wire clamp on at the top, and pull it around on the left side, then, by using the needle nose pliers, have the wire clamp at about 3:00 o clock on the right, there is a spring on that wire clamp, put that at 3:00 o clock as well, pull down as hard as you can at the spring which stretches the clamp, then work it around with your other hand, or your wife if she isn't scared like mine was
Best of luck,
Parts Used:
-
FRANK from COVINA, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
PARTSSELECT IS THE PROBLEM
I asked PS if I purchase from them, will I get the new version level sensor or the old version in a sealed bag that has the new number on the bag.
They guaranteed I would get the newest version level sensor inside of the bag. I had this problem with the past 3 vendors) So i spent double the $ to purchase from them. it arrived, bag had new part # inside was the OLD PART numbered item! The would not respond! The link for the install wont work! I just need the newer part and the calibration procedure t make this right or a refund!
NO SUPPORT for PARTSSELECT!
They guaranteed I would get the newest version level sensor inside of the bag. I had this problem with the past 3 vendors) So i spent double the $ to purchase from them. it arrived, bag had new part # inside was the OLD PART numbered item! The would not respond! The link for the install wont work! I just need the newer part and the calibration procedure t make this right or a refund!
NO SUPPORT for PARTSSELECT!
Parts Used:
-
David from ROUND LAKE PK, IL
-
Difficulty Level:Very Difficult
-
Total Repair Time:30 - 60 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer Would Drain But Not Spin
Removed rear cover (6 screws) unpluged harness from motor control and removed same. Replaced motor control reinstalled harness. Replaced rear cover. Parts used motor control board.
Parts Used:
-
Nelson from Middletown, NY
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Wrench (Adjustable)
0 of 26 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!