79579993510 Kenmore Refrigerator - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Air Cleaner Filter Assembly – Part Number: ADQ73214408
$41.67
In Stock
Air Cleaner Filter Assembly
Part #ADQ73214408
This air filter helps keep your fridge smelling fresh and your food lasting longer. It uses carbon to trap odors and clean the air inside your refrigerator. If you notice bad smells or your fridge tells you it’s time, it’s probably time to replace the filter—usually every six months. It fits LG and some Kenmore Elite models. To install, just turn off the power, swap out the old filter, and reset the filter light once the new one’s in place.
Refrigerator Water Filter LT700P – Part Number: AGF80300702
$77.99
In Stock
Refrigerator Water Filter LT700P
★★★★★
★★★★★
(4)
Part #AGF80300702
This refrigerator water filter replacement is for 2010 LG refrigerators that have either forward French doors or are the four-door dispensing models. This filter is designed to minimize impurities that can cause ill-tasting water or an unpleasant smell. It reduces sediment, dirt, rust, limescale, sand, and many other contaminants that can be harmful to your health and the life of your appliance. This filter should be replaced every 6 months or 200 gallons to ensure top quality performance. To remove your unwanted filter, press the push button to open the filter cover (water may spill from the hole), pull out the old cartridge in a downward motion. To install the new filter, make it so the ears are in the horizontal position and push the new cartridge into the housing until it stops. Push the filter upward until it is secure. Click the cover to lock it in place. Run water for approximately 5 minutes to prep the filter for use, and discard water. Reset the “filter reset” button if applicable.
Door Bin – Part Number: AAP73252202
$82.45
In Stock
Door Bin
★★★★★
★★★★★
(4)
Part #AAP73252202
Add useful storage space inside a refrigerator door with this clear plastic door bin. It holds bottles, jars, drinks, and condiments where they are easy to see and reach. The bin measures about 13-1/2 inches wide and 4-1/4 inches high. Its shaped base is about 9-1/2 inches deep on one side and 10-1/8 inches deep on the other. Installation requires no tools. Place the bin slightly above the mounting points, then slide it down until it locks into place. Compare the size, shape, and side mounts with the original bin before ordering.
Handle Screw – Part Number: MJB63190001
$13.15
In Stock
Handle Screw
★★★★★
★★★★★
(2)
Part #MJB63190001
This handle screw, also known as a mounting bolt, is a mounting screw to help secure the door handle to your refrigerator door. If your handle is loose, you may just need to tighten the screw. If your screw is missing or broken, it may need to be replaced. There are multiple handle screws on your fridge, please consider ordering extra as they commonly wear at the same rate. This is about 1 inch long and metallic in color.
Door Shelf Bin Assembly – Part Number: AAP73252302
$60.45
In Stock
Ice Water Tube Assembly – Part Number: AJR56656503
$40.65
In Stock
Ice Water Tube Assembly
Part #AJR56656503
Connector,Tube – Part Number: 4932JA3009A
$20.85
Special Order
Connector,Tube
Part #4932JA3009A
Refrigerator Water Reservoir – Part Number: AJL72911502
$67.05
In Stock
WATER INLET VALVE – Part Number: AJU72992603
$120.78
In Stock
WATER INLET VALVE
Part #AJU72992603
Refrigerator Glass Shelf – Part Number: MHL42613229
$57.15
Special Order
Water Filter Bypass Plug – Part Number: ABN73019101
$38.19
In Stock
Water Filter Bypass Plug
Part #ABN73019101
Micro Switch – Part Number: 6600JB3001C
$35.15
In Stock
Micro Switch
Part #6600JB3001C

Questions And Answers for 79579993510

Ask our experts a question about this model and we'll get back to you as soon as possible!

Sort by:
  • 1
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Tom - For model number 79579993510
December 28, 2019
Both of the evaporator fans not running when compressor and condenser are running. I have ohmed out the three wires on each fan motors all leads show open. How can i check to make sure the motors are bad or if it's another problem?
Chris Boyle Profile
Hello Tom and thank you for writing. Take the input voltage to the motor using the volt ohmmeter. The motor-specified voltage must be present in all three phases. Examine the motor's electrical connections and terminals. ... Remove the motor voltage and disengage the motor from the machine that it is running. ... Check the motor for heat or burnt smell. We hope this helps. Please contact us anytime if you require further assistance.
1 person found this instruction helpful.
Was this helpful?
Thank you for voting!
Tom - For model number 79579993510
December 30, 2019
Hello, in regards to testing the evaporator fan motors they are 13v dc . To be sure about what has been recommended, should i get 13v dc on all of the three leads to the motor? And will that be a test between any combination of the three leads?(red, black and purple).And if i get on voltage coming to the motor what else can i check?
Chris Boyle Profile
Hello Tom and thank you for writing. Use a multimeter to check the electrical resistance of the motor. Plug the probes from the multimeter into the two wires you identified coming out of the evaporator motor together, then turn the multimeter on and set it to resistance, or Ohms. Markdown the reading on the multimeter, then compare it to the resistance reading the evaporator motor should have. You can find the correct resistance specifications for the evaporator motor in the owner’s manual, an application-specific repair manual, or on the manufacturer’s website. If the reading doesn’t match the manufacturer’s specifications, the evaporator motor needs to be replaced. For your convenience, we have attached the link to your manual with specifications. We hope this helps. Good luck with your repair. https://www.nodevice.com/user-manuals/refrigerators/kenmore/79579983510/1069540?page=229 Here is also the manufacturer's phone number: Kenmore 888-536-6673
1 person found this instruction helpful.
Was this helpful?
Thank you for voting!
Charles - For model number 79579993510
January 24, 2023
Refrigerator freezer not working But frigerator is check the coils nice and clean Any suggestions
Chris Boyle Profile
Hello Charles, thank you for reaching out. If your refrigerator freezer is not working then the problem appears to be with the Compressor, part number PS12739218. If that does not help then the issue is likely to be with the Evaporator Fan Motor, part number PS10058947. Customer service is always available to help you place an order if you are having trouble doing so. Good luck with your repair!
$104.62
In Stock
Evaporator Fan Motor
$390.07
In Stock
Compressor
1 person found this instruction helpful.
Was this helpful?
Thank you for voting!
  • 1

Common Symptoms of the 79579993510

How this model fails, and the parts that fix it.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Replaced Old Molded Gasket with new one
9 of 9 people found this instruction helpful.
  • Megan from Elk Grove, CA
  • Very Easy
  • Less than 15 mins
  • Screw drivers
For the right side of the refrigerator door, just pulled off the old gasket and replaced it with the new one. Old gasket came off easily. Just had to pull it off. No screws on the right side. Just pushed the new one in place in the groove on the door.

For the left side, needed a Phillip’s screwdriver to remove the flap first. H elps to have a second person hold the door from moving. Once flap was off, pulled the old gasket off and installed the new one just like the right side. Then screwed the flap back on once the gasket was in the groove properly.

Initially after install, it seemed like the magnet on the door was not strong enough but after a couple of days, the magnet seems a lot stronger, sealing the air out. Very happy I replaced it. It was a lot simpler to replace than I thought it would be.
Was this helpful?
Thank you for voting!
Ice Maker Quit Making Ice
8 of 12 people found this instruction helpful.
  • Jeff from HUMBLE, TX
  • Very Easy
  • Less than 15 mins
  • Screw drivers
For this model the ice maker is very easy to replace. All it takes is a phillips head screwdriver. There are two wire connections you have to unplug. Easy out easy in. You do not have to disconnect the water line, just make sure the line is lined up correctly when you reinstall the new icemaker. It seems to take approximately 8 hours befo re you start getting ice again. If you have this same model, you already know this ice maker is very slow in making ice and is not able to keep up with daily usage of ice for a household of 3.
Was this helpful?
Thank you for voting!
Moldy and torn gaskets
5 of 6 people found this instruction helpful.
  • Konnie from SALEM, OR
  • Easy
  • Less than 15 mins
  • Screw drivers
Once I U tubed the the removal and replacement of the gaskets it was super easy. The right gasket change was easy without tools. The left gasket required me to remove the mullion first, which is why I used Utube.
Was this helpful?
Thank you for voting!