79579983510 Kenmore Refrigerator - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Air Cleaner Filter Assembly – Part Number: ADQ73214408
$41.67
In Stock
Air Cleaner Filter Assembly
Part #ADQ73214408
This air filter helps keep your fridge smelling fresh and your food lasting longer. It uses carbon to trap odors and clean the air inside your refrigerator. If you notice bad smells or your fridge tells you it’s time, it’s probably time to replace the filter—usually every six months. It fits LG and some Kenmore Elite models. To install, just turn off the power, swap out the old filter, and reset the filter light once the new one’s in place.
Refrigerator Water Filter LT700P – Part Number: AGF80300702
$77.99
In Stock
Refrigerator Water Filter LT700P
★★★★★
★★★★★
(4)
Part #AGF80300702
This refrigerator water filter replacement is for 2010 LG refrigerators that have either forward French doors or are the four-door dispensing models. This filter is designed to minimize impurities that can cause ill-tasting water or an unpleasant smell. It reduces sediment, dirt, rust, limescale, sand, and many other contaminants that can be harmful to your health and the life of your appliance. This filter should be replaced every 6 months or 200 gallons to ensure top quality performance. To remove your unwanted filter, press the push button to open the filter cover (water may spill from the hole), pull out the old cartridge in a downward motion. To install the new filter, make it so the ears are in the horizontal position and push the new cartridge into the housing until it stops. Push the filter upward until it is secure. Click the cover to lock it in place. Run water for approximately 5 minutes to prep the filter for use, and discard water. Reset the “filter reset” button if applicable.
Door Bin – Part Number: AAP73252202
$82.45
In Stock
Door Bin
★★★★★
★★★★★
(4)
Part #AAP73252202
Add useful storage space inside a refrigerator door with this clear plastic door bin. It holds bottles, jars, drinks, and condiments where they are easy to see and reach. The bin measures about 13-1/2 inches wide and 4-1/4 inches high. Its shaped base is about 9-1/2 inches deep on one side and 10-1/8 inches deep on the other. Installation requires no tools. Place the bin slightly above the mounting points, then slide it down until it locks into place. Compare the size, shape, and side mounts with the original bin before ordering.
Handle Screw – Part Number: MJB63190001
$13.15
In Stock
Handle Screw
★★★★★
★★★★★
(2)
Part #MJB63190001
This handle screw, also known as a mounting bolt, is a mounting screw to help secure the door handle to your refrigerator door. If your handle is loose, you may just need to tighten the screw. If your screw is missing or broken, it may need to be replaced. There are multiple handle screws on your fridge, please consider ordering extra as they commonly wear at the same rate. This is about 1 inch long and metallic in color.
Door Shelf Bin Assembly – Part Number: AAP73252302
$60.45
In Stock
Ice Water Tube Assembly – Part Number: AJR56656503
$40.65
In Stock
Ice Water Tube Assembly
Part #AJR56656503
Connector,Tube – Part Number: 4932JA3009A
$20.85
Special Order
Connector,Tube
Part #4932JA3009A
Left Side Connector Rail – Part Number: 4932JA1010A
$27.45
In Stock
Left Side Connector Rail
Part #4932JA1010A
Refrigerator Water Reservoir – Part Number: AJL72911502
$67.05
In Stock
WATER INLET VALVE – Part Number: AJU72992603
$120.78
In Stock
WATER INLET VALVE
Part #AJU72992603
Glass Shelf – Part Number: MHL42613220
$73.65
Special Order
Glass Shelf
Part #MHL42613220
This glass shelf provides storage space in your refrigerator above the crisper. Shelves can crack and chip due to frequent use, and should be replaced immediately if cracks start to appear. This shelf measures approximately 30.5 inches wide by 15 inches deep and is for LG refrigerators. Replacing a damaged shelf is easy, carefully remove the faulty shelf and install the new one. Be sure to wear protective gloves if the existing shelf is cracked or broken.
Water Filter Bypass Plug – Part Number: ABN73019101
$38.19
In Stock
Water Filter Bypass Plug
Part #ABN73019101

Common Symptoms of the 79579983510

How this model fails, and the parts that fix it.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Replaced Old Molded Gasket with new one
9 of 9 people found this instruction helpful.
  • Megan from Elk Grove, CA
  • Very Easy
  • Less than 15 mins
  • Screw drivers
For the right side of the refrigerator door, just pulled off the old gasket and replaced it with the new one. Old gasket came off easily. Just had to pull it off. No screws on the right side. Just pushed the new one in place in the groove on the door.

For the left side, needed a Phillip’s screwdriver to remove the flap first. H elps to have a second person hold the door from moving. Once flap was off, pulled the old gasket off and installed the new one just like the right side. Then screwed the flap back on once the gasket was in the groove properly.

Initially after install, it seemed like the magnet on the door was not strong enough but after a couple of days, the magnet seems a lot stronger, sealing the air out. Very happy I replaced it. It was a lot simpler to replace than I thought it would be.
Was this helpful?
Thank you for voting!
Ice Maker Quit Making Ice
8 of 12 people found this instruction helpful.
  • Jeff from HUMBLE, TX
  • Very Easy
  • Less than 15 mins
  • Screw drivers
For this model the ice maker is very easy to replace. All it takes is a phillips head screwdriver. There are two wire connections you have to unplug. Easy out easy in. You do not have to disconnect the water line, just make sure the line is lined up correctly when you reinstall the new icemaker. It seems to take approximately 8 hours befo re you start getting ice again. If you have this same model, you already know this ice maker is very slow in making ice and is not able to keep up with daily usage of ice for a household of 3.
Was this helpful?
Thank you for voting!
Moldy and torn gaskets
5 of 6 people found this instruction helpful.
  • Konnie from SALEM, OR
  • Easy
  • Less than 15 mins
  • Screw drivers
Once I U tubed the the removal and replacement of the gaskets it was super easy. The right gasket change was easy without tools. The left gasket required me to remove the mullion first, which is why I used Utube.
Was this helpful?
Thank you for voting!