The dishwasher roller assembly connects to the dishrack, and is located in the lower level of the dishwasher. It allows the dishrack to easily slide in and out. If the lower rack keeps falling off the...
If your dishwasher is leaking or not cleaning as well as it used to, the door gasket might be the culprit. This flexible rubber seal fits around the tub and keeps water and steam inside during each cy...
This drain hose assembly is designed for use with select LG washing machines and includes both the flexible rubber hose and plastic connectors. It efficiently channels used water from the washer tub t...
This part is the replacement inlet valve for your dishwasher. It is approximately 4-1/2 inches by 3-1/2 inches. The water inlet valve in your dishwasher connects to the water source and solenoid wire...
This pump casing assembly is designed for use in select LG dishwasher models and houses several key components responsible for water circulation during wash and drain cycles. It includes the motor, wh...
Keep your dishwasher running smoothly with this LG mesh filter assembly. It traps food particles and debris so they don’t clog the drain or spray arms, helping your dishes come out cleaner every time....
This lower cover assembly, also known as a sump cover, is an essential part of the dishwasher’s internal system. It shields the pump and other components from food particles, helps filter debris from ...
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Daniel
July 27, 2025
I need the little clips that hold the divider panels in the lower dish tray
For model number 72214673710
Hi Daniel, thank you for reaching out. The holders you are looking for are part number PS12391986, PS12391989, and PS12391988. We hope that helps!
Was this helpful?
Thank you for voting!
Joel
July 28, 2025
I am having to turn off the breaker, wait 10 minutes then turn back on to get the dishwasher to work.
What is wrong?
For model number 72214673710
Hi Joel, thank you for reaching out. The issue might be with the main control board, part number PS12385247. It manages all the functions of the dishwasher, including washing, draining, and drying. You may need to replace it to fix the issue. We hope this solves your problem!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Replacing this pump is pretty easy. Disconnect the power and drain hose, and pull your dishwasher out from the counter. Lay it on its side on a towel. There WILL be spillage. Disconnecting the pump is simple. There are a couple hoses, one single wire connection (the thermistor) and one multi-wire plug. The pump is held in place by a pair of thick rubber holders which can be pulled off by hand. That's it!
After removing the pump, I disassembled it to find out why these fail so soon. It's a very poor design. I found that the nose of the electric motor, where the bearings are located, sits in a plastic cup formed by the top of the pump body. Any leakage from the pump around the motor shaft will be held in place against the motor bearing. It has no place to go. This causes rusting of the bearing. I expect I'll be replacing this one in a few years. :(
But kudos to PartsSelect for getting the right pump assembly for me, after getting the wrong one from another supplier!
The inside gasket deteriorates over time - However replacement is easy. the main thing you have to remember is after you remove the old gasket, install the new one starting at the middle top of the tub and work your way down both sides. Also, don't push the gasket all the way in...only enough to hold in place. When you close the door the gasket will form a better seal around the door.
Ordered the roller from Parts Select, slid the roller over the little spindle sticking out of the bottom rack and snapped it in place. Job done in less than one minute.
