66463 Microwave - Instructions

No repair- just replaced glass turntable.
Right part I needed with first try

PartSelect had the turntable I needed at the best price. Ordering was easy, but best of all, the part was delivered next day. I was able to insert the new turntable plate into the microwave and it was good as new.

Opened the box and popped it in. No problem with that.

The part was sent to me the next day! And it was the right part. Awesome!

set the table on the support ring

After watching a few youtube videos, I used a phillips SD to take controll pannel off to access the switches that sense when microwave door is closed. Swapped out all 3 switched and mocrowave works like new. $20 fix (shipping included)

This is the second replacement tray we have in installed. The first one ( Not From Here ) we had for less than 5 months, we made a bag of popcorn, and about 5 minutes later we heard a crash, not knowing where the noise came from we dismissed it. The next day we opened the microwave a saw the plate had shattered. So we hope that this will not do the same thing.

My 8 year old daughter cleaned the inside of the microwave with enough water to rival a tsunami. Resulted in a clean microwave with a fried out motor that no longer revolved. Part came quickly. Took cover and bottom off to get to the part. One screw held it on and a plug. Removed those, put on new part and she was good to go. No trip to home depot today.

My unit is a wall mount/cabinet/built-in model. The repair is actually fairly simple once you determine that the actual microwave is just a component of the entire unit, and that it (the microwave) can be easily removed from the unit. I did not figure this out until after I removed the entire unit (disconnect the power supply, lift the entire bulky, heavy unit out of the cramped space in the cabinet, etc). Once I got it out I figured out how easy it is to remove the actual oven - a couple of screws, literally. The unit is a bit bulky, but not particularly heavy and is quite manageable. I did this entire process alone.

I got the oven out, rolled it on it's side and found the plate to access the motor. The plate is located on the bottom/underside of the unit. The plate is nothing more than a section of the underside of the metal housing that has been cut-out as an access point. This "cut-out" is not complete - that is, not completely cut out so as to all the plate to stay in place without the need for screws, etc, until you actually have to use it. I used a pair of dykes to cut the couple of points still connecting this plate, removed the two phillips screws to remove the motor, disconnected the two wires connected, then reversed to complete the repair. You then flip the cut-out plate over/rotate it, and some screw holes line up. Find a couple of small screws, and re-attach the plate to cover the motor.

The actual fix is really easy, again, once you figure out the simple way to remove the oven. I am an idiot, so you will probably find this much easier. I could probably do this repair now, after my experience, in less than 30 minutes (probably less than 15 minutes). I probably save a couple hundred $ by doing it myself so was well worth the time to do it. Good luck.

1. Remove 2 screws on edge of door, these hold door trim on.
2. Using putty knives, gently lever outer door trim away from door, moving knives around door.
3. Door trim will come off, at bottom move insulation and remove lower handle screw. Remove upper handle screw.
4 Instal new handle, a reverse of #3, do not over tighten screws.
5. Replace door trim, it snaps into place, it may require a small whack.
6. Have a pat on the back for saving $100.

Read some instructions and easily found the fuse. Replaced it. Still didn't work. Took control panel off to check door switches. Nothing I read mentioned a second fuse. Tested and it to had blown. Ordered another one. Popped them in. Done.

I looked up a YouTube video of someone with a similar over the oven microwave. That helped me get into the area behind the control panel where the door switches are. I checked the springs and the cam rocker? The thing that actually hits the button on the switch when the door closes. They were in good condition so I assumed the door switch was bad. There are two so I just purchased one figuring (hoping) that only one was bad. And lo and behold only one was bad. Bing bam boom. Put it all back together and I'm set. Not too difficult. Took a week of work because it takes like 50 days to ship. My kitchen looked like a hurricane after image because of all the parts scattered everywhere.

I ordered the part according to the Model number, inserted the part very easily, (and I am soooo challenged in that area) and now it turns again. :)

replace one of the four rack supports which was melting

Fun and easy fix for my kids.

The countdown timer was working but no "cooking" happening. Did not hear the familiar sound of the heating part working.

Determined it might be some simple switches for under $15 dollars. Bought one of each. They allow the microwave to turn on/activate by signaling that the door is properly latched. My wife noticed that it was failing and then failed over the course of about a day. Several times where it worked, then did not work. The timer was counting down one time and then when she opened the door the microwave heating component turned on. Guess it had activated the switch as she was opening the door.

Procedure to repair
- Unplug
- Remove two screws on front top - allows you to remove the vent. Realized there was a charcoal filter there that I had never replaced so ordered that after the fix.
- Remove two screws to pull off the front right panel (area where your microwave buttons are) One at the top under the before mentioned vent and one under the microwave on the far right corner.
- Have someone hold the panel because wiring is to short to place it on a ledge while connected or take a picture and remove connections. I simply held it while my daughter undid the micro switches.
- Carefully remove micro switches. There were two "orange" button ones so I chose the top one to replace along with the green button one that I had ordered, so I simply pulled an orange from the bottom and a green from the top latch area. You may have remove the part that holds the switches since it was a little tough with the wires in the way and not knowing how the switches stay put.
- plug in new switches and place in the brackets that hold them in place
- reverse everything you did.
Viola - a working microwave vs purchasing a brand new for several hundred dollars or having to call in a technician.I love that my young kids did this project with me and we actually got it running. Don't like to have to throw away more items at the landfill.

Semi-Handy Man