Models > 6443A

6443A Norge Washer - Overview

Sections of the 6443A

[Viewing 13 of 13]
Keep searches simple, eg. "belt" or "pump".
Drive Belt - 51 inches long – Part Number: WP21352320
Drive Belt - 51 inches long
★★★★★
★★★★★
(12)
PartSelect #: PS11738882
Manufacturer #: WP21352320
This V-style drive belt is about 51" long and 3/8" wide. This part is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt encounter wear and tear.
$22.33
  In Stock
Snubber Ring – Part Number: WP21002026
Snubber Ring
★★★★★
★★★★★
(15)
PartSelect #: PS11738845
Manufacturer #: WP21002026
$13.49
  In Stock
Lid Hinge Pin – Part Number: WP35-2045
Lid Hinge Pin
★★★★★
★★★★★
(5)
PartSelect #: PS11741781
Manufacturer #: WP35-2045
This lid hinge pin is just over an inch long. It is all white in color and is made entirely of plastic. Sold individually.
$26.04
  In Stock
Lid Hinge – Part Number: WP35-2044
Lid Hinge
★★★★★
★★★★★
(7)
PartSelect #: PS11741780
Manufacturer #: WP35-2044
This lid hinge in an inch and a half long and is used for some washing machines. It is all white in color and it is made entirely of plastic.
$12.90
  In Stock
Transmission Pulley and Bearing Kit – Part Number: 12002213
Transmission Pulley and Bearing Kit
★★★★★
★★★★★
(10)
PartSelect #: PS2003651
Manufacturer #: 12002213
Also known as Thrust Bearing Kit. This kit includes the pulley, washer, thrust bearing, 2 upper race washers and 1 lower race washer. These parts are NOT available separately - they are ONLY availab...
$78.16
  In Stock
Drain Pump with Pulley – Part Number: WP35-6465
Drain Pump with Pulley
★★★★★
★★★★★
(10)
PartSelect #: PS11741799
Manufacturer #: WP35-6465
This pump has 2 ports. This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
$97.89
  In Stock
Hose Clamp – Part Number: WP596669
Hose Clamp
PartSelect #: PS11743008
Manufacturer #: WP596669
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
$9.36
  In Stock
Screw – Part Number: WP489483
Screw
PartSelect #: PS11742755
Manufacturer #: WP489483
This screw is sold individually.
$15.67
  In Stock
Hose Clamp – Part Number: WP285655
Hose Clamp
PartSelect #: PS11740613
Manufacturer #: WP285655
This hose clamp is sold individually.
$10.60
  In Stock
Tub to Pump Hose – Part Number: WP21001915
Tub to Pump Hose
★★★★★
★★★★★
(3)
PartSelect #: PS11738836
Manufacturer #: WP21001915
$29.84
  In Stock
Leveling Leg and Pad – Part Number: WP25001119
Leveling Leg and Pad
★★★★★
★★★★★
(2)
PartSelect #: PS11740563
Manufacturer #: WP25001119
This part includes locknut.
$13.96
  In Stock
Screw, 8/18 x 3/8 – Part Number: WP90767
Screw, 8/18 x 3/8
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$9.36
  In Stock

Questions And Answers for 6443A

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Symptoms of the 6443A

[Viewing 14 of 14]
Noisy
Fixed by
these parts
Show All
Shakes and moves
Fixed by
these parts
Show All
Leaking
Fixed by
these parts
Show All
Pumps but will not spin
Fixed by
these parts
Show All
Burning smell
Fixed by
these parts
Show All
Will not drain
Fixed by
these parts
Show All
Lid or door will not open
Fixed by
these parts
Show All
Spins slowly
Fixed by
these parts
Show All
Lid or door won’t close
Fixed by
these parts
Show All
Will not agitate
Fixed by
these parts
Show All
Will not stop filling with water
Fixed by
these parts
Show All
Will Not Start
Fixed by
these parts
Show All
No hot or cold water
Fixed by
these parts
Show All
Timer will not advance
Fixed by
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
washing machine was making alot of noise
I found the water pump bearings were going bad from humidity. I replaced the pump with a new one and it runs quiet again.
Parts Used:
Drain Pump with Pulley
  • David from Boca Raton, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Wrench set
554 of 562 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
One of the plastic hinge pins brroke
I used a flat screw driver to push in on the releases so I could raise the top of the machine. I then used a torx tool to remove both parts of the hinge, and then used a #2 phillips screw driver, on the new screws I'd also ordered, to re-attach both of the hinge parts. Every thing went just as anticipated.
Parts Used:
Lid Hinge Pin Lid Hinge Screw
  • Allen from North Little Rock, AR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
510 of 513 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Load Grinding/Rubbing Noise in Rinse and Spin Cycles
First unplug the washer for the electrical outlet. You will need to tip the washer back to get to the bottom of the machine. There you will see the belt that drives the transmission and the water pump from the motor. Remove the belt and set it to the side. Then you will need to gain access to the top side of the machine by gently using a screwdriver to pry the front of the top up off the front panel on both sides then hinge it back out of the way. Use a nut driver to remove the two screws on the inside edge of the front panel and remove the front panel. Once the front panel is off you will see the water pump on the right hand side as you face the front of the machine. Remove the hose clamp on the water pump with the flat head screw driver or nut driver and use a pair of pliers to remove the compression clip on the water pump. Remove the 4 bolts holding the water pump in place. Reverse the entire process to put it back together. This job was very easy and I was only without a washer for 2 days because of partselect.com.
Parts Used:
Drain Pump with Pulley
  • Doug from Port Richey, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
139 of 151 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!