62140419 General Electric Dryer - Overview

This authentic, white Drum Bearing Slide, also known as the bearing drum slide, glide, or pad, is a plastic, easy-to-install part for your dryer. It replaces the dryer's front drum slide to allow for easier movement. You'll know if this part is an issue if your dryer is unable to tumble properly or is very noisy. Damage can come from reg...Read moreular use. The part attaches to the outermost side of the bearing. Check both slides for signs of wear, because they often wear at the same rate, and should be replaced at the same time; there are 2 of these particular slides per dryer. This part is sold individually, so you'll need to purchase multiple parts if replacing both at the same time.

This original equipment manufacturer Drum Bearing Slide is a plastic, green, easy-to-install part for your dryer. It replaces the dryer's front drum slide to allow for easier movement. You'll know if this part is an issue if your dryer is unable to tumble properly or is very noisy. Damage can come from regular use. As the slides start to...Read more break down it may cause your dryer to make noise or not dry clothes in the usual amount of time. You will need to purchase two for both sides of your dryer. They attach to the outer-most sides of the bearing. The manufacturer recommends replacing both slides at the same time. Take this opportunity to clean out the lint and dust in the dryer, to keep it running smoothly. This is a genuine replacement part that comes directly from the manufacturer. This item is sold individually. The part attaches to the outermost side of the bearing. Although this part is denoted as being "Green" in its title, many users and technicians have noted that its true colour is closer to a dark gray or black.

This OEM Timer Knob is a white plastic knob which can be easily installed onto your machine's timer rod, in order to control the timer. If the part breaks off, it should be replaced. Refer to your user manual and model number to see if this part is right for you. It is a three-inch-diameter part that accepts a D-shaped shaft. To replace y...Read moreour faulty knob, simply pull the existing knob straight off the shaft and install the replacement back onto the shaft. No tools are required. This item is sold individually and is not part of a set. The timer knob contains the insert as well as the knob itself.

TThe door strike for your dryer is mounted on the dryer frame that the door shuts onto. It fits into the door catch on the door and keeps the door closed. If the door strike is damaged or missing, the door will not lock properly and not only will this cause the door to swing open, but it won’t allow the dryer to start properly. It is a small piece of metal, about 1 inch in length and is sold individually.

This Genuine OEM door latch is designed for use with a wide range of GE clothes dryers. Constructed from a combination of durable metal and plastic, the latch is mounted onto the dryer frame to securely hold the door closed during operation. A properly functioning latch is essential for safe and efficient drying cycles. Sold individual...Read morely, this replacement part may require a screwdriver and a pair of pliers for removal and installation. Replacing a worn or broken latch helps restore proper door alignment and ensures the appliance operates as intended.

This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Helps keep your dryer running as smoothly as possible with as little noise as possible. NOTE: Bearing plate has slot in it for ground strap.

This part is the replacement high-limit thermostat or safety thermostat for your dryer. The high-limit thermostat is found on the upper right-hand side of the heater housing, and it cuts off power to the dryer motor if the temperature reaches an unsafe level. If you push the start button and nothing happens, the high-limit thermostat shou...Read moreld be tested for continuity and replaced if the contacts are open. Be sure to disconnect power to the dryer before you begin this repair. This part is sold individually and is an OEM part.

This part is on the outer door of the dryer.

This belt has a length of 87 inches, width of 1/4”, flat, with 4 ridges.

A door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open.

The adjustable leveling screws on the bottom of your dryer can be screwed in or out to lower or raise the leg level. If one of the leveling screws is stripped, damaged, or missing, you may not be able to create a level base for your dryer. The leveling screw has a hexagon-shaped gray plastic foot, with a screw that is approximately 1 inch...Read more in length. To replace a damaged screw, simply turn the old screw to the left, until it can be removed. Then, simply screw the new leveling screw into place on the bottom of the dryer, making sure it is the same height as the other 3 leveling screws.

Note: The insulators on the housing are NOT sold separately.