This manufacturer-approved Refrigerator Pantry End Cap Kit, also known as the Refrigerator Drawer Support, is a kit containing all parts of the Pantry End Cap. It snaps into place on the appliance’s ...
$56.35
In Stock
Order within the next 10 hrs and your part ships today!
This water filter purifies water going to the water dispenser and sometimes the icemaker as well. This part should be replaced if it is causing reduced water flow or just replaced periodically per the...
This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are mos...
$13.36
In Stock
Order within the next 10 hrs and your part ships today!
NOTE: This replacement ice maker mechanism does NOT come with a cover, shut off arm, a wire harness, or the mounting hardware. Those must be ordered separately, or you can use the existing parts.
$177.43
In Stock
Order within the next 10 hrs and your part ships today!
This board will need to be programmed upon installation. The electronic control board is used in refrigerators to monitor and manage the temperature settings, such as cooling or defrosting times. If y...
$264.22
In Stock
Order within the next 10 hrs and your part ships today!
This includes both the run capacitor and the start relay. The capacitor helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer.
The start ...
$96.83
In Stock
Order within the next 10 hrs and your part ships today!
This part mounts on the crisper drawer cover and is used to limit the amount of air that gets into the crisper.
$14.15
In Stock
Order within the next 10 hrs and your part ships today!
Questions And Answers for 59675529400
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ernie
October 23, 2023
Quit cooling so I replaced it but now I would like to try and fix it. I have had it unplugged for a while, when I plug it init runs and gets cold inside but after it shuts down due to reaching the proper temperature it will try to come back on but never cools down again
For model number 59675529400
Hello Ernie, thank you for your inquiry. Based on our understanding, the issue is most probably with the electronic control board, part number PS11755733. You may need to replace it to fix the issue. Glad to be of help!
So far I have replaced the control circuit board, defrost thermostat and starter with capacitor. After being unplugged to replace each new part it will run when I plug it back in and cool down to proper temperatures and shut off but after a while when it tries to restart I get a humming noise at the compressor for 10 seconds and then a “click” from the compressor area but the compressor will not start so it starts getting warm inside. If I leave it plugged in I will get the humming noise about every two minutes and then the click but compressor never starts
For model number 59675529400
Hi Ernie, thank you for reaching out. Since you have replaced some of the most common parts but the issue persists, you may need to check the compressor, part number PS2580803, as it is most likely faulty or begining to fail and may need to be replaced. Glad to be of assistance!
Pressed in the end of the filter cover, lowered it down part way. Twisted the old filter 1/4 turn and removed it. Set in the sink to drain. Inserted new filter and twisted it to lock. closed cover. Done. Total time @ 1 Minute.
Interior surface of ice tray felt rough & flaky (coating deteriorated) so cubes would not release. Unplug appliance. Remove timer cover by hand pressure @ edge. Remove single attachment screw & bracket at lower front of icemaker. Disconnect wiring harness from socket @ rear of compartment. Tricky part was determining what type of connection held the other two attachment points along the long edge of the icemaker. I did not have repair manual or useful drawing but looked @ PartsDirect pic of side brackets & used a small mirror to confirm that mine were also some sort of "snap in" attachment. Remove icemaker unit by pushing upward and outward on the unit. I takes a good bit of pressure and will pop loose, but be careful not to break attachment bracket from freezer wall. Scavenge shut off bar and wiring harness from old icemaker once you have it out & attach to new one before installing it back in freezer. Again, you might find a mirror useful to align those pesky snap-in brackets with the new unit. Since you probably kept your freezer running while waiting for the part, the plastic snap-ins will be cold and brittle. I warmed them up first by applying a dampened cloth heated in the microwave to make them a little more pliable. A good push of the new unit towards the snap-ins along with some upward force will get it stable. Reattach the metal screw in bracket & connect the wiring harness to rear plug... and don't forget to plug the whole thing back in. It will take awhile for the first batch of cubes dump as the timer may need to cycle completely around to get to the fill cycle... be patient. Dump the first couple of batches of cubes just to make sure you're free of any residue.
unplugged refrigerator and shut off water, removed one screw and loosened two more, after removing one side of the ice bucket rail, unplugged electrical from old ice maker. Then I removed the bail and out on new one, reinstalled ice maker in reverse order from taking it out.