59672013014 Kenmore Refrigerator - Instructions

I knew the chances of all the freon leaking out was unlikely so I looked at the wiring to the compressor and there was a capacitor and a starter/overload so i figured I would start there. I went on line and found the parts at this site and they were less than the minimum service call charge for a service tech so I figured what the heck let's give her a shot so I did give it a shot. I ordered the parts and they were there in less time than a service tech could come out and i installed the parts and guess what for 90.00 in parts and 15 minutes in time I repaired my refrigerator. Thanks guys, It took less time to order the parts than it did to make the repair so thanks, your website rocks and is very well designed so my hat is off to you guys!

Removed the fruit & veggie drawers & the deli (pantry) drawer. Took out the 3 screws, removed the attached parts, put them on the replacement part, reattached it and put the drawers back in.

Here's the part I want to share: PartSelect had a expanded diagram showing the correct part and sufficiently detailed to figure out the repair before the part arrived. That's why I ordered from them. Secondly, I ordered the part Thursday morning--and the thing was sitting on my porch when I came back in from my evening out Saturday--2 days later!!!

Remove food off of lower shelf, remove the two produce drawers, remove large lower drawer, remove glass shelf, remove three screws holding end cap in place. Once end cap was removed the drawer track could be removed and placed on new end cap. Installation of new end cap took less than 5 minutes. Most of the time spent was removing/replacing food and cleaning the shelf/bins. PartSelect was awesome BTW!

Remove Crisper drawers from Bottom Shelf.
Remove glass from the top of Bottom Shelf.
Drop new Crisper frame center rail into slots on the top of the Bottom Shelf shelf.
Replace glass onto the top of the Bottom Shelf.
Slide drawers between left and right guides and the Crisper frame center rail.

Total repair time less than one minute.
No tools required.

1. remove deli draw
2. remove glass top & end caps
3. remove screws on side of end cap
4. remove end cap
5. remove crisper control connection bars & rear ductwork
6. reinstall crisper control connection bars & rear ductwork
7. install new end cap & rear ductwork
8. install glass top & end caps
9. install deli draw & cover

The video on website is very good and explains everything in detail. Just follow the directions. This is EASY!!!!

I used a flat-head screwdriver to pop out the old light rocker switch. Then, I unplugged the wires, plugged them into the new light rocker switch, and then popped the new switch into the hole. That's it! Lights began working again.

removed both crisper drawers, glass shelving, etc. removed the screws that held the part in place and replaced it with the new part. it was that easy

The easiest thing to do was pull the ice make off. After taking the 3 screws out of the wall of the freezer, take a screwdriver (flathead) and push on the tab for the electrical plug and wiggle the cord out. Then you can take 3 screws out for the main cover and another 2 screws on the next cover. There's the part, pop it out and replace holding pins and start the process of putting back together the opposite way you took it apart.

removed ice maker and wire shelf. removed back panel screws and tilted forward. removed 2 screws holding motor bracket. swapped fan blade and reassembled

Removed two screws that held cover plate. remove cover plate. Remove water hose, and clamp, by compressing clamp with pliers. Remove fill tube by pulling HARD, from back.

Replace fill tube, check to be sure that it entered ice maker properly. Replace hose and clamp.
Replace cover and screws.

I used a flat screwdriver and released the lock tab on the bottom of the light switch, and pried the switch out, being careful to not damage the plastic around the mounting place of the switch, unplugged wiring from old switch, plugged in the new one and pushed the new switch into place. Job finished light switch now working.

Not a bad job at all. Took out the vegetable bins above, the glass cover and the sliding drawer. Then took out the screws holding the end caps on to the refrigerator wall. You can remove the metal slide at this time or after you take the old piece out. Then you re-install the metal slide on the new piece and screw it back in. THe right hand side is trickier because you also have to remove the mechanism in the back that controls the humidity inside the bin as well as the control lever in the front, so that you can install them on the new end cap. All the parts either snap on or you have to twist them slightly. We repaced both end caps as well as cleaned things really well in about 45 minutes, with 2 adults and a 10 yr old working together.

1. I had to remove the cold cut drawer.
2. Remove the two screws for the sliding track and then the sliding track.
4. Remove the two crisper drawers as well as the glass and the two supports for the glass.
3. Remove the two screws for the end cap. This is accomplished by gently lifting up at the front of the part. You will find another three parts that are attached to the end cap. One is the slider that controls the tempetature, it is attached to a long plastic rod that is connected to the back side of the end cap by pressure clip points. The other end of the plastic rod is connected to a piece that is mounted to the back wall of the refridgerator. this is removed by gently pulling the entire unit forward until it comes loose from the back wall. Once the entire assembly is removed, The plastic rod must be released from teh back of the end cap. This will allow both ends to be disconnected from the slider at the front and the piece that was attached to the back wall by rotating each end to allow the removal of the components fronm the end cap. Once everything is removed, you are ready to complete the repair by reversing the removal process.

The ice maker was not getting water. I hotwired the water valve by switching the connectors for the water dispenser and ice maker water valves and water flowed into the icemaker when the water dispenser lever was pushed. I wronly assumed the water valve was good. I removed the icemaker and determined that the gear motor was not getting power in the position the icemaker had stopped.In this position, the thermostat determines when the motor gets power so I replaced the thermostat. The icemaker still would not get water! As it turns out, the water solenoid was sticking due to a deteriorated rubber washer which let the solenoid plunger get too far out of the magnetic field. I replaced the water solenoid assy and all is well. Don't get fooled by hotwiring the valve. If it isn't getting water, the solenoid probably is the culprit.