592-49045 Samsung Washer - Overview
Sections of the 592-49045
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Washer Door Lock Latch
PartSelect #: PS11745016
Manufacturer #: WP8182634
This part helps keep your front-load washer safe and working properly. It locks the door during cycles so it doesn’t open unexpectedly, and it also tells the washer when the door is shut so it can sta...
$128.93
In Stock
Order within the next 9 hrs and your part ships today!
Shock Damper Front
PartSelect #: PS4212219
Manufacturer #: DC66-00470A
$45.02
In Stock
Order within the next 9 hrs and your part ships today!
Hex Head Bolt
PartSelect #: PS4205366
Manufacturer #: DC60-40137A
$9.44
In Stock
Order within the next 9 hrs and your part ships today!
Tapping Screw
PartSelect #: PS4133205
Manufacturer #: 6002-000520
$2.99
In Stock
Order within the next 9 hrs and your part ships today!
Drain Pump Assembly - 120V 60Hz
PartSelect #: PS4204638
Manufacturer #: DC31-00054A
No Longer Available
Water Temperature Thermistor
PartSelect #: PS4214274
Manufacturer #: DC90-10128N
$46.84
In Stock
Order within the next 9 hrs and your part ships today!
Washer Tub Gasket Seal
PartSelect #: PS4213806
Manufacturer #: DC69-00804A
$33.51
In Stock
Order within the next 9 hrs and your part ships today!
Motor Assembly
PartSelect #: PS4204678
Manufacturer #: DC31-00111A
$184.69
In Stock
Order within the next 9 hrs and your part ships today!
Oil Seal
PartSelect #: PS4208713
Manufacturer #: DC62-00223A
$31.09
In Stock
Order within the next 9 hrs and your part ships today!
Common Symptoms of the 592-49045
[Viewing 9 of 9]Lid or door won’t close
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Shaking and Moving
Fixed by
these parts
these parts
Show All
Locking Issues
Fixed by
these parts
these parts
Show All
Water Filling Issues
Fixed by
these parts
these parts
Show All
Door latch failure
Fixed by
these parts
these parts
Show All
Spinning Issues
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
front load washer latch replacement
1. remove the three screws from the top backside of the top panel
2. push the top panel to the rear 1/8 to 1/4 inch
3. lift/rotate top panel from rear to front, set aside.
4. remove the three wire connectors from latch.
5. use #15 Torx to remove the three screws from the latch.
6. remove and replace part using top opening.
7. reverse order to finish.
2. push the top panel to the rear 1/8 to 1/4 inch
3. lift/rotate top panel from rear to front, set aside.
4. remove the three wire connectors from latch.
5. use #15 Torx to remove the three screws from the latch.
6. remove and replace part using top opening.
7. reverse order to finish.
Parts Used:
-
James from Vilonia, AR
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
198 of 242 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door lock was in the locked position and door could not close
I bought a new door lock for 132 dollars (item number PS2037196).
Ultimately you have to get to the inside of the machine where the door lock is located in order to see if you will need this door lock that I bought.
DISCONNECT POWER FROM MACHINE.
First take off the top by taking off the 2 screws on the back of the machine.
Second take off the control panel, I believe there are about 5 or 6 screws for that.
(there's also a screw when you open up the detergent compartment on the bottom left- also, a lever must be pushed in order for the compartment to come off- it MUST be taken off).
Third unscrew the top of the front white plate.. there should be a 5 or 6 screws for that.
You don't need to take off the entire front plate.
Finally unscrew 3 screws that hold the door lock in place .. make sure your hands is in the machine- the back of door lock to catch the lock when you're on the last screw.
Gently take out the door lock from the side with the cables attached by holding the white metal door open (it bends).
Try to pull on the bottom of the door lock (its a manual release). If it doesn't release you need to buy a new door lock like I did... if it does release then you don't need a door lock and just reassemble.
(Note: You can also try plugging in the machine and THEN pulling down on the manual release. When I tried this the door lock just vibrated and nothing happened so I bought a new door lock.)
If you have the new door lock continue here:
Take out all 3 cables on the old door lock by pressing on the corresponding clips.
Attach the new door lock with the correct cables. Assemble machine back together.
Thats it.
Ultimately you have to get to the inside of the machine where the door lock is located in order to see if you will need this door lock that I bought.
DISCONNECT POWER FROM MACHINE.
First take off the top by taking off the 2 screws on the back of the machine.
Second take off the control panel, I believe there are about 5 or 6 screws for that.
(there's also a screw when you open up the detergent compartment on the bottom left- also, a lever must be pushed in order for the compartment to come off- it MUST be taken off).
Third unscrew the top of the front white plate.. there should be a 5 or 6 screws for that.
You don't need to take off the entire front plate.
Finally unscrew 3 screws that hold the door lock in place .. make sure your hands is in the machine- the back of door lock to catch the lock when you're on the last screw.
Gently take out the door lock from the side with the cables attached by holding the white metal door open (it bends).
Try to pull on the bottom of the door lock (its a manual release). If it doesn't release you need to buy a new door lock like I did... if it does release then you don't need a door lock and just reassemble.
(Note: You can also try plugging in the machine and THEN pulling down on the manual release. When I tried this the door lock just vibrated and nothing happened so I bought a new door lock.)
If you have the new door lock continue here:
Take out all 3 cables on the old door lock by pressing on the corresponding clips.
Attach the new door lock with the correct cables. Assemble machine back together.
Thats it.
Parts Used:
-
Suryakant from Cortlandt Manor, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
67 of 76 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Washer became unbalanced and broke the latch on door
Had to take the entire front of the washer off to replace the door latch.
Parts Used:
-
Glenn from Las Vegaas, NM
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers
32 of 44 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!