502254210 Craftsman Lawn Tractor - Overview

Diagrams for 502254210

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Filter-fuel – Part Number: 845125
$12.95
In Stock
Filter-fuel
Part #845125
This is a genuine part that is supplied by the original manufacturer for use with Craftsman wood lathes and lawn mowers. The fuel filter removes debris before it reaches the carburetor in your equipment. This part made of plastic and is sold individually. For installation, you will need a socket wrench to remove any shrouds or panels, and a pair of needle nose pliers to aid you.
Key Set – Part Number: 691959
$13.95
Special Order
Key Set
Part #691959
This is an OEM replacement part for Briggs and Stratton, Murray, Snapper, and Simplicity engines. When engaged the ignition key starts the lawn tractor. This part is made of metal and is sold in a set of two. There are no tools needs to use this part, as it comes pre-assembled and really to use.
Plug-oil Drain – Part Number: 690946
$10.95
Special Order
Plug-oil Drain
Part #690946
An authentic item that is supplied by the original manufacturer for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It is a high-quality replacement for a faulty or missing oil drain plug that came installed on a new unit. Please make sure to check the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind it is made of durable metal and is sold individually.
Nut 8Pk – Part Number: STD541237
No Longer Available
Nut 8Pk
Part #STD541237
Tube-dipstick – Part Number: 691257
No Longer Available
Tube-dipstick
Part #691257
Collar Stop – Part Number: STD551237
No Longer Available
Collar Stop
Part #STD551237
Carriage Bolt – Part Number: STD533107
No Longer Available
Carriage Bolt
Part #STD533107
Washer 8Pk – Part Number: STD551125
No Longer Available
Washer 8Pk
Part #STD551125
Screw – Part Number: STD522506
No Longer Available
Screw
Part #STD522506
Screw 5Pk – Part Number: STD523707
No Longer Available
Screw 5Pk
Part #STD523707
Washer 8Pk – Part Number: STD551025
No Longer Available
Washer 8Pk
Part #STD551025
Pin 8Pk – Part Number: STD560907
No Longer Available
Pin 8Pk
Part #STD560907
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Carberator gummed up from sitting in storage. Fuel gone bad in the tank
6 of 7 people found this instruction helpful.
  • Robert from BATON ROUGE, LA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Socket set
With a 12-in-one nut screwdriver I removed the two bolts holding the breather cover and air filter. Then I used about a 9/16 deep socket ratchet to remove the nuts holding the breather housing to the carburetor assembly studs. A pair of needle nose pliers was used to disconnect the throttle then I wriggled the breather cover away from t he carburetor so I could get to the fuel line. I managed to pull the fuel line off the carburetor and from the shut-off valve at the tank. The carburetor slid freely and easily off the carburetor studs and I was careful not to damage the carburetor gasket since none came with the new carburetor. I used a single edge razor blade to free the gasket from the old carburetor. A very small amount of silicone lube was used on the gasket and then I sandwiched the old gasket between the carburetor intake and the new carburetor and attached the throttle connection. Before beginning the reassembly I unscrewed the shut-off valve from the tank and used a funnel to drain the very old fuel into a 5-gallon bucket. I made sure the valve was clean by spraying carburetor cleaner through it and did the same with the old fuel line, making sure everything was clear of any obstruction. Then replace the breather assembly back over the carburetor studs, snugged the nuts back on and then replaced the air filter and cover. I re-attached the fuel line to the fuel valve and the carburetor, added a half gallon of clean fresh fuel and was ready for a smoke check. Pulled the starter rope three times with the choke full on, then turned to half-choke and the puppy started right off. I then turned the choke completely off and the engined purred along. I then exercised the generator by plugging in and running a number of power tools for about 15 minutes. Followed standard shut off procedures and the generator is ready for use. Saving the old carburetor to be cleaned and held on reserve for the future. Might want to have another gasket handy or some gasket material should it have to be replaced in the future.
Was this helpful?
Thank you for voting!