4UP72 (Type 1) DeVilbiss Compressor - Overview

This is a genuine replacement part manufactured for use with outdoor power equipment and air compressors. This nut is used to fasten various part assemblies on a range of different products. This nut is sold individually, please see model diagram for part usage and location.

When using an air compressor, moisture naturally builds up inside the tank as air is compressed. If this water isn’t drained regularly, it can lead to internal rust and damage over time. That’s where the drain valve comes in—it allows you to release the built-up water and keep your tank in good condition. Located at the bottom of the tank...Read more, this valve should be opened after each use to prevent corrosion and extend the life of your compressor. If you tend to leave air in the tank for long periods, water accumulation can be even more significant. This replacement drain valve features a thread size of 18 TPI and is sold individually. Regular maintenance with a working drain valve helps ensure safe and efficient compressor operation.

This replacement valve plate assembly is a high quality item designed for use on Craftsman air compressors. It is a genuine manufacturer sourced item that is used to control the airflow into the cylinder. Once the piston starts traveling up, the reeds on the valve plate open and air is sent into the air tank. Overtime the reeds will get w...Read moreorn eventually requiring valve plate replacement. One metal valve plate with reed valves and two rubber seals are included in this assembly. When replacing this valve plate assembly it is also a good time to replace the head gaskets which are sold separately. You will need a wrench set to complete this repair.

This is an OEM part sourced directly from the manufacturer. The front shroud is commonly found in compressors from DeVilbiss. This part is made of high-quality plastic, and is used to cover the front of the motor assembly. You will require a screwdriver when replacing this part. This item is sold individually.

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. rnrnThere are many causes for O-Ring failure. The most common among power tools are: • Extrusion and Nibbling - The O-ring has ragged, tattered edges. ...Read moreThese are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that it too rough, contains grit or is too smooth to allow lubrication. • Over Compression - The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening - The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking - The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.

This is an authentic Porter Cable replacement part, sourced from the original manufacturer for use with air compressors. The special tray tool is commonly used to store pneumatic tools and to cover the motor shroud. This tool tray is available as an individual replacement part, please see model diagram for associative parts.

This is an authentic OEM part. The filter is used with air compressors from Porter Cable, DeVilbiss, and Black & Decker. The foam filter is used to prevent dirt and debris from entering and potentially damaging the pump. A hex driver, or screwdriver may be needed to install this item and it is sold individually.

Restore air pressure in a compatible oil free air compressor with this cylinder service kit, it includes a cylinder sleeve, compression ring, piston rod screw, and two sealing rings, replace worn parts when the compressor runs but makes little or no air, unplug the compressor and release all tank pressure before repair, check the model and type number before ordering.

This is an authentic Porter Cable replacement part for air compressors. The shroud bracket is used to attach to the rear shroud and act as an anchor point for the front shroud. The bracket is made of high-quality metal. This item is sold individually.

This is a manufacturer approved replacement muffler used on air compressors. Muffler softens the noise coming from the engine and provides an additional filtering. This Kit includes the Plastic Filter Holder, Foam Filter, Two (2) Plastic Pins used to attach it and a Metal Mesh Screen.

It is an OEM component which is designed for use with air compressors. This special nut sleeve assembly secures the pressure relief tube to the pressure switch. It is a high-quality replacement for a damaged or a missing hardware that was installed on a new unit. One durable metal nut sleeve assembly is included. A wrench will be needed t...Read moreo perform this repair. Check the appropriate diagrams for your model to ensure the proper replacement procedure. Make sure to drain the air before starting this repair.

This is an authentic replacement part manufactured for use with Porter Cable air compressors. The safety valve is used to prevent the tank from overpressurizing by letting air out of the tank when a specific pressure is met. Safety valves have specific pressure tolerances specific to the model of air compressor it is important to match th...Read moree valve to your model of compressor. This safety valve is available as an individual replacement part.