This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
$27.85
In Stock
Order within the next 12 hrs and your part ships today!
This washer shock absorber mounting pin is a small but essential fastener that secures the shock absorber to the outer tub of a front-load washing machine. By holding the shock absorber firmly in plac...
$29.73
In Stock
Order within the next 12 hrs and your part ships today!
This front-load washing machine door boot seal is a flexible rubber component designed to create a watertight barrier between the washer’s door and the inner tub. It plays a critical role in preventin...
$189.61
In Stock
Order within the next 12 hrs and your part ships today!
Ensure proper drainage and protect your washer from damage with this durable tub-to-pump hose, designed for front-load washing machines. This genuine replacement part carries water from the tub to the...
$129.39
In Stock
Order within the next 12 hrs and your part ships today!
Have you been facing leaking issues with your washing machine? Our genuine and high-quality Frigidaire Bellows Spring Clamp could be the simple solution you need. Designed for your washing machine's d...
$44.35
In Stock
Order within the next 12 hrs and your part ships today!
Reduce vibrations and noise during wash and spin cycles with this shock absorber kit, designed to stabilize the washer tub for smooth, quiet operation. Made from durable plastic and rubber components,...
$99.29
In Stock
Order within the next 12 hrs and your part ships today!
This genuine OEM drain pump is an essential component for removing water from the washer tub during the drain cycle. Built from durable materials, including impact-resistant plastic and stainless stee...
$220.59
In Stock
Order within the next 12 hrs and your part ships today!
This spring helps keep the rubber seal around your washer’s door in place, stopping leaks and keeping everything running smoothly. If your washer is leaking or the seal looks loose, this part might be...
$64.00
In Stock
Order within the next 12 hrs and your part ships today!
Order within the next 12 hrs and your part ships today!
Questions And Answers for 41741102000
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Michael
February 10, 2023
On dispenser drawer Part diagram 45 what about replacing Part 50 Detergent and softer tray that fits in drawer
For model number 41741102000
Hello Michael, thank you for writing in. On the Diagram, Item 45, PS11766113 is the Drawer. And, Item 50, is only Drawer Conveyer PS2350419 which attaches to the underside of the Dispenser Drawer. The drawer front and housing have been discontinued. We hope this helps.
Bought new part. #1 Lesson learned: Always inspect the actual part number of the ordered/received part. Verify with number marked on the item somewhere. We did not do this and turned out we reinstalled a slightly smaller bellow (wrong part number received in shipment). We were able to fully install it but it was minutely not laying perfectly around the diameter. So minor we did not notice. We did have great difficulty installing though. Anyway, after 1st test run, bellow already had developed a small hole in bottom right quadrant from rubbing on the drum. Left a bunch of gray powdery debris on the drum too. We did not realize error until that point. Took bellow off again to verify part number on it. It was wrong. That explained why the door was so very tight to close and difficult to open. Other than all that, use the video to do the install. It was free to view and easy to follow.
1 you have to order a new motor control board 2 unscrew the back panel 3 unscrew the top panel 4 unscrew the bracket 5disconnect the old motor control board 6 connect the new motor control board
