41741101000 Kenmore Washer - Overview
Sections of the 41741101000
[Viewing 4 of 4]
Manuals & Care Guides for 41741101000
Click to downloadInstall
Installation Instructions
(8.39MB)
Manual
Owner's Manuals
(4.57MB)
Specs
Product Specifications Sheet
(0.28MB)
Wiring
Wiring Diagram
(0.28MB)
Keep searches simple, eg. "belt" or "pump".
Screw
PartSelect #: PS417463
Manufacturer #: 131302800
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
$28.95
In Stock
Single Shock Mounting Pin
PartSelect #: PS417323
Manufacturer #: 131268300
This washer shock absorber mounting pin is a small but essential fastener that secures the shock absorber to the outer tub of a front-load washing machine. By holding the shock absorber firmly in plac...
$29.73
In Stock
Bellow
PartSelect #: PS2342392
Manufacturer #: 134616100
This front-load washing machine door boot seal is a flexible rubber component designed to create a watertight barrier between the washer’s door and the inner tub. It plays a critical role in preventin...
$114.31
In Stock
Tub to Pump Hose
PartSelect #: PS2378397
Manufacturer #: 134639910
Ensure proper drainage and protect your washer from damage with this durable tub-to-pump hose, designed for front-load washing machines. This genuine replacement part carries water from the tub to the...
$134.47
In Stock
Water Inlet Valve
PartSelect #: PS2349248
Manufacturer #: 134637810
This water inlet valve works with washers
$205.28
In Stock
CLAMP
PartSelect #: PS2349238
Manufacturer #: 134616300
Have you been facing leaking issues with your washing machine? Our genuine and high-quality Frigidaire Bellows Spring Clamp could be the simple solution you need. Designed for your washing machine's d...
$52.95
In Stock
Shock Absorber Kit
PartSelect #: PS8689635
Manufacturer #: 5304491700
Reduce vibrations and noise during wash and spin cycles with this shock absorber kit, designed to stabilize the washer tub for smooth, quiet operation. Made from durable plastic and rubber components,...
$101.90
Special Order
Door Catch Screw
PartSelect #: PS417465
Manufacturer #: 131302901
Sold individually.
$13.89
In Stock
Drain Pump - 120V 60Hz
PartSelect #: PS2378516
Manufacturer #: 137240800
This genuine OEM drain pump is an essential component for removing water from the washer tub during the drain cycle. Built from durable materials, including impact-resistant plastic and stainless stee...
$123.57
In Stock
Dispenser Inlet Gasket
PartSelect #: PS1145695
Manufacturer #: 134371300
Sold individually.
$55.60
In Stock
SPRING
PartSelect #: PS2349237
Manufacturer #: 134616200
This spring helps keep the rubber seal around your washer’s door in place, stopping leaks and keeping everything running smoothly. If your washer is leaking or the seal looks loose, this part might be...
$64.00
In Stock
Common Symptoms of the 41741101000
[Viewing 4 of 4]Leaking
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Water Filling Issues
Fixed by
these parts
these parts
Show All
Lid or door won’t close
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Original bellow had 2 largish holes in the upper left quadrant; random leaking.
Bought new part. #1 Lesson learned: Always inspect the actual part number of the ordered/received part. Verify with number marked on the item somewhere. We did not do this and turned out we reinstalled a slightly smaller bellow (wrong part number received in shipment). We were able to fully install it but it was minutely not laying perfectly around the diameter. So minor we did not notice. We did have great difficulty installing though. Anyway, after 1st test run, bellow already had developed a small hole in bottom right quadrant from rubbing on the drum. Left a bunch of gray powdery debris on the drum too. We did not realize error until that point. Took bellow off again to verify part number on it. It was wrong. That explained why the door was so very tight to close and difficult to open. Other than all that, use the video to do the install. It was free to view and easy to follow.
Parts Used:
-
Michelle from Loves Park, IL
-
Difficulty Level:Very Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
19 of 24 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
ELECTRONIC COMPONENT
Still waiting on the part. It apparently is on back order and I'm still waiting to get the part to try and repair the dryer.
I estimate an hour to replace the part if I ever get the part.
I estimate an hour to replace the part if I ever get the part.
Parts Used:
-
Elmer from JACKSONVILLE, FL
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer stops in middle of cycle and E53 appears on the screen
1 you have to order a new motor control board
2 unscrew the back panel
3 unscrew the top panel
4 unscrew the bracket
5disconnect the old motor control board
6 connect the new motor control board
2 unscrew the back panel
3 unscrew the top panel
4 unscrew the bracket
5disconnect the old motor control board
6 connect the new motor control board
Parts Used:
-
Baruch from HURLEYVILLE, NY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!