40141 LG Washer - Overview

Diagrams for 40141

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washing Machine Drain Pump – Part Number: 4681EA2001T
$138.95
In Stock
Washing Machine Drain Pump
★★★★★
★★★★★
(111)
Part #4681EA2001T
The drain pump and motor assembly may also be known as the washer drain pump and is a part for your washer. The drain pump helps expel water from the washing machine. The drain pump is activated after the spin cycle speed is maintained for a specific period of time. To make this installation you will need a Phillips screwdriver, a small flat-blade screwdriver, a pair of needle-nose pliers, and a pair of slip-joint pliers. Note that the pump casing is not included. This medium-difficulty repair may vary, but can generally be started by disconnecting power, then removing the top of the washer by taking out the four back screws and two small brackets. Then, remove the front panel by taking out the two screws and eight tabs that should be taken from the top. Moving down the front of the washer, remove the door, latch, tub gasket, and drain cover. Disconnect the drain hoses and clip from under the drain assembly, and install new assembly from there. Reassemble parts in direct reverse order -- taking photos during disassembly and keeping parts clearly organized can help here. Despite the number of steps, you will only need a standard Phillips screwdriver to complete this repair.
Water Inlet Valve - Hot – Part Number: 5220FR2006H
$67.05
In Stock
Water Inlet Valve - Hot
★★★★★
★★★★★
(18)
Part #5220FR2006H
This hot water inlet valve is designed to regulate water flow into the washing machine during operation. Featuring a standard hose fitting inlet and a single water outlet, it opens as needed to allow hot water into the appliance. If the valve is defective, you may notice slow filling, no filling at all, or water leaks. A simple way to test the valve is to unplug the washer when the issue occurs—if water continues to flow, the valve is likely faulty and should be replaced. The part measures approximately 3 inches in length by 3 inches in width and is sold individually.
Shock Absorber Kit – Part Number: 383EER3001J
$57.15
In Stock
Shock Absorber Kit
★★★★★
★★★★★
(2)
Part #383EER3001J
This kit includes 1 shock absorber and 2 pins.
Door Lock Assembly – Part Number: EBF49827801
$72.55
In Stock
Door Lock Assembly
★★★★★
★★★★★
(6)
Part #EBF49827801
This door lock assembly is a critical component in compatible washing machines, responsible for confirming that the door is securely closed before initiating a wash cycle. When functioning properly, it communicates with the control system to engage the locking mechanism. A faulty switch may prevent the door from latching, opening, or starting the cycle. Located behind the front panel, replacement requires removal of the door gasket and access to the internal housing. Sold individually.
Inlet Valve Assembly – Part Number: 5221ER1003A
$93.03
In Stock
Inlet Valve Assembly
★★★★★
★★★★★
(18)
Part #5221ER1003A
If your washer isn’t filling properly or skipping parts of the cycle, this water valve might be the issue. It controls cold water flow for the bleach dispenser and prewash cycles. The valve connects with a standard hose and has three outlets—two pointing to the right and one to the left—all at a 45-degree angle. It’s a genuine part and easy to install, but be sure to unplug your washer and turn off the water before starting.
Drain Hose Assembly – Part Number: 5215ER2002G
$74.75
In Stock
Washer Motor Rotor Position Sensor – Part Number: 6501KW2001B
$46.15
In Stock
Washer Motor Rotor Position Sensor
★★★★★
★★★★★
(5)
Part #6501KW2001B
If your washer isn’t spinning properly, this motor rotor position sensor might be the solution. It keeps track of how fast and in which direction the rotor is turning, sending that information to the control board to help your machine run smoothly. Installation is simple, but be sure to unplug the washer first to stay safe.
Detergent Dispenser – Part Number: 3891ER2003A
$38.27
In Stock
Detergent Dispenser
★★★★★
★★★★★
(3)
Part #3891ER2003A
The blue plastic detergent dispenser holds the detergent and then dispenses it into the washer during the wash cycle. If the detergent dispenser is broken, lost, or if the detergent is not dispensed during the wash cycle, you may need to replace it. The dispenser is approximately 4-inches wide, 4.5-inches long, 2-inches tall and is a genuine OEM part.
Pump Filter – Part Number: 383EER2001A
$34.22
In Stock
Pump Filter
★★★★★
★★★★★
(3)
Part #383EER2001A
This replacement pump filter, also known as a filter assembly, is a genuine OEM part for your washer or washer/dryer combo. Before beginning this repair, turn off the power and water supply to your washer. The filter assembly may need to be replaced because it is broken or is leaking water. To locate the filter assembly, pry open the small door on the front of the washer, using a flat-blade screwdriver. Unplug the drain hose next to the filter and drain the water into a bucket. Then unscrew the pump filter, and replace with your new one.
Washer Gasket – Part Number: 4036ER2003A
$43.95
In Stock
Washer Gasket
★★★★★
★★★★★
(2)
Part #4036ER2003A
This genuine OEM drum seal gasket prevents water from leaking between the outer tub and spin basket of your washer. It is made of black rubber and measures 2.5 inches in diameter. If your washer is leaking, and running noisier than usual, check for wear on the gasket, and to ensure it is properly fitted.
Washer Hose Connector – Part Number: 5214FR4006G
$15.35
In Stock
Washer Hose Connector
★★★★★
★★★★★
(1)
Part #5214FR4006G
This part is the replacement connector hose or clean-out drain hose for your washer. It is black in color and is sold individually. The connector hose drains water out of the washer if the drain cycle is not working. If the hose breaks, it will not be able to drain the water properly, and you may experience a water leak. Be sure to disconnect your washer from the power source, as well as the water source before you begin this repair. This is an OEM part sourced directly from the manufacturer.
Shock Absorber Kit – Part Number: 383EER3001S
$63.75
Special Order
Shock Absorber Kit
Part #383EER3001S
This kit includes 1 shock absorber and 2 mounting pins.

Exact Part matches for your search term

Guide Pin – Part Number: 40141
No Longer Available
Guide Pin
This part number matches the current model number 40141
Part #40141

Common Symptoms of the 40141

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washing maching wouldn't drain
592 of 761 people found this instruction helpful.
  • Jorge from Apple Valley, CA
  • Easy
  • 1- 2 hours
  • Screw drivers
Removed the top of the washer by removing the 4 back screws and 2 small brackets. Then I removed the front panel, this was actually the hardest part, 2 screws and 8 tabs that you pop out carefully from the top of the panel. I only disconnected the power button and was able to rest the panel on top of the washer. The rest of the washer cam e apart quickly just moving down the front of the washer and removing the door, latch, tub gasket, drain cover. Removing the pump was just a mater of disconnecting the drain hoses, and one clip under the drain assembly. 3 screws attach the drain to assembly to the pump and only 2 wires that are clearly marked. Reassembly is just going back through in reverse order of disassenbly. The best thing about this is that it all comes apart with a standard phillips screwdriver.
Was this helpful?
Thank you for voting!
noisy operation, sometimes did not drain, gave OE code
60 of 81 people found this instruction helpful.
  • Michael from RALEIGH, NC
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Thank you for the very helpful YouTube video. After watching the video, I was able to diagnose the problem, buy the part from your website, and complete the repair. This is my personal machine - I am not a professional repairman.
Was this helpful?
Thank you for voting!
Inlet valve leak
34 of 37 people found this instruction helpful.
  • John from Northport, NY
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Followed directions on the video and went like a charm. Very impressed with service and video
Was this helpful?
Thank you for voting!