3702B Makita Laminate Trimmer - Overview

This item is available as an individual replacement part. The hex nut is made out of metal. A wrench might be helpful during the installation of this part. It might break or strip over time and will need replacing. This genuine item is supplied by the original equipment manufacturer for use with blowers, drills, grinders, nailers, rotary hammers, routers, sanders, saws, and trimmers made by Makita.

This item is a genuine Makita part that has been sourced from the original manufacturer to be used with trimmers, circular saws, sanders, routers, nailers, reciprocating saws, laminate trimmers, and planers. The flat washer is used with different types of power tools and the application of the washer can vary based on the model of the equipment. This item is available as an individual replacement part.

This is an authentic Makita replacement part that has been sourced from the original manufacturer to be used with circular saws, table saws, masonry saws, planers, demolition hammers, and angle cutters. The washer has multiple applications based on the model of the power tool. It is recommended to review your model's diagram to verify this washer's compatibility. The washer is sold individually.

This is a genuine item that is supplied by the original equipment manufacturer for use with Makita equipment. It is a high-quality replacement for a missing or damaged screw that was originally installed on a new unit, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hard...Read moreware. Keep in mind this high-quality thumb screw is made of durable metal with a plastic grip and is sold individually.

This is a genuine Makita replacement part that has been sourced from the original manufacturer to be used with circular saws, miter saws, and laminate trimmers. The washer is used for spacing and to disperse the pressure put on a part assembly by a nut or bolt across a wider surface area. This item is sold individually, please see your model's illustrated diagram for the washer's location and usage.

This manufacturer sourced replacement pin is made out rubber and it is sold individually. It acts as a cushion/spacer in a variety of Makita power tools. This is a standard piece of hardware and it has multiple applications based on your tool. Please refer to diagrams for correct application.

This brush cap is a genuine OEM sourced replacement part. It is commonly used on a variety of Makita power tools. This brush cap helps to secure the carbon brush in the brush holder. This cap has external threads that will thread into the opening in the housing. This item is made out of durable plastic and it is sold individually. It has ...Read morea convenient slot that makes it easy to secure or remove it using only a flat-head screwdriver.

This genuine manufacturer-sourced part is specially designed for Makita power tools. It is an important component which provides a tight seal between connected components. Unfortunately, over time it will wear out and it may begin to crack eventually requiring a replacement. To ensure the correct repair procedure, refer to the appropriate...Read more diagrams for your model. Note, this high-quality insulation washer is made of durable material and is sold as an individual item. A screwdriver will be needed to take apart and reassemble the tool when performing this repair.

This is a Ball Bearing that is sealed on both sides. This is a genuine Makita replacement part that is sold individually. • Ball bearings minimize friction between 2 parts in your tool that would otherwise spin and rub against each other. The balls or rollers take the load and spin, distributing the weight evenly while the minimal co...Read morentact area of the balls reduce friction. This reduces wear on the tool and allows it to run smoothly. • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

This Ball Bearing is sealed on both sides. This is a genuine Makita replacement part that is sold individually. • Ball bearings minimize friction between 2 parts in your tool that would otherwise spin and rub against each other. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact are...Read morea of the balls reduce friction. This reduces wear on the tool and allows it to run smoothly. • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

This is an original Makita replacement part. The screw is designed by the manufacturer for use in laminate trimmers and blade sharpeners. This part is made of high-quality plastic and metal, and may be used in various locations in the machine, depending on model. Please refer to the parts diagram to be sure of ordering the correct part...Read more. No tools are required when replacing this item. Simply remove the old part and screw the new one into place. This product is sold individually.

This rubber piece is a genuine Makita manufactured part. It is manufactured for various power tools. A cord protector guards the wires from damage caused by motion and strain. Damaged cords must be replaced to avoid safety hazards. A replacement cord is sold separately. This item consists of one (1) cord protector. This is a simple and qu...Read moreick repair. • Unplug machine • Remove the casing • Detach cord from tool • Slide cord protector onto cord • Reattach wires and casing • Test power tool