363G Kenmore Dishwasher - Overview

Models starting with 363G

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sump Housing – Part Number: WD18X213
$84.13
Special Order
Sump Housing
★★★★★
★★★★★
(2)
Part #WD18X213
This part is the replacement sump housing or sump insert for your dishwasher. It is made of plastic and is approximately 7 inches by 5 inches. The sump housing is attached to the bottom of the dishwasher tub and collects water for the pump. If your dishwasher is leaking, you may need to replace the sump housing. Be sure to disconnect the dishwasher from the water and power source before you begin this repair. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.
Impeller and Seal Kit – Part Number: WD19X10032
No Longer Available
Impeller and Seal Kit
★★★★★
★★★★★
(2)
Part #WD19X10032
This part helps stop your dishwasher from leaking. This kit includes the impeller, seal, blade, filter, skidder and skidder holder.
Motor and Pump Kit – Part Number: WD26X10013
$275.11
Special Order
Motor and Pump Kit
★★★★★
★★★★★
(4)
Part #WD26X10013
This pump and motor kit replaces many old style pump and motor kits that were manufactured since 1970. The instructions are included with this kit to help you to make it adaptable to your dishwasher. NOTE: This is a completely redesigned kit by the manufacturer and now includes the drain solenoid.
Drain Hose – Part Number: WD24X10014
$74.40
Special Order
Drain Hose
★★★★★
★★★★★
(1)
Part #WD24X10014
This drain hose is an OEM, manufacturer-approved replacement part for your dishwasher. The drain hose filters out the wastewater from the dishwasher. If there is a hole in it, water will leak out of your dishwasher. Shut off the water and power to the unit before beginning this repair. Accessing the drain hose involves unscrewing the dishwasher and pulling it out. Remove the clamp holding the hose in place to its connection under the sink, using a 5/16ths socket. Disconnect the fill line. Use a 1/4 inch nut driver to loosen the clamp at the other end of the drain hose. Keep a towel handy for any water still inside. Keep the clamps for use on your new drain hose. Reinstall all hoses and lines in reverse order.
Detergent Cup Door Spring – Part Number: WD3X764
$46.95
Special Order
Armature Link – Part Number: WD1X1316
$40.95
Special Order
Float Switch – Part Number: WD21X479
$24.05
Special Order
Float Switch
Part #WD21X479
Water that fills your dishwasher lifts this float, and when it reaches a certain level, it acts as a trigger for the float switch. The float triggers the float switch to shut off, thereby shutting off the flow of water into the dishwasher.
Dishwasher Hose Clamp Kit – Part Number: WH1X2036
$22.95
Special Order
Dishwasher Hose Clamp Kit
Part #WH1X2036
This hose clamp kit contains two clamps. The smaller of the two is an inch in diameter while the larger of the two is two inches in diameter.
Dishwasher Clamp Sump – Part Number: WD1X1392
$19.99
Special Order
Dishwasher Clamp Sump
Part #WD1X1392
Finish Dishwasher Cleaner – Part Number: WX10X10209
No Longer Available
Finish Dishwasher Cleaner
Part #WX10X10209
This dishwasher cleaner cleans, freshens, and helps maintain your dishwasher. It hygienically cleans hidden grease and lime scale from filters, spray-arms and pipes. It is safe for septic systems and contains no phosphorus.
Drain Solenoid Repair Kit – Part Number: WD21X802
No Longer Available
Drain Solenoid Repair Kit
★★★★★
★★★★★
(1)
Part #WD21X802
This kit includes the armature and link assembly. You may need the solenoid bracket which is sold separately. This valve opens in order for the water to drain out of the dishwasher.
Sump Cover – Part Number: WD12X417
$71.60
Special Order
Sump Cover
Part #WD12X417

Common Symptoms of models starting with 363G

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water not draining from dishwasher
267 of 316 people found this instruction helpful.
  • Mark from Morgan Hill, CA
  • Easy
  • 1- 2 hours
  • Screw drivers, Socket set
I had never done work on my dishwasher - I was a rookie in this area. Turns out the work itself was quite simple. Pulled the dishwasher out, turned it over, and was able to easily replace the motor and pump assembly. The drain tube was also an easy replace. A couple key notes:

1. I also purchased a new drain solenoid and impell er kit. Note that both of these items are already included in the Motor and Pump kit replacement. There is no need to by both, now I have extras.

2. The end of the drain tube has to be trimmed if you are routing the drain tube to an air gap mounted on your kitchen sink. You have to cut the large diameter end of the tube to get to the narrow portion that will fit on your air gap.

3. The first cycle you run with the new motor/pump assembly is noisy. When you first fire it up the components in the pump are all dry, and they squeal until the water gets to them. I initially thought I had done something wrong, but once the water started flowing all the peculiar sounds cleared up.
Was this helpful?
Thank you for voting!
Motor was getting noisier every time we used the dishwasher. We knew it was just a matter of time before it totally quit.
48 of 53 people found this instruction helpful.
  • Glenn from Clemmons, NC
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
The most difficult part was removing the dishwasher from below the counter. Once that was complete, I simply turned the washer onto it's front surface to access the pump easier. Simply disconnected the electrical connectors, loosened the three hose clamps holding the hoses to the pump. Lastly removed a stiff arm bracket holding the pum p. Reversed the order to install the new one using a longer bracket provided with the new unit. Hooked up the electrical connections last and slid the washer back in place. The washer runs like new now and is not making noise. The replacement part was a perfect match.
Was this helpful?
Thank you for voting!
dishwasher pump valve leaking at shaft
40 of 47 people found this instruction helpful.
  • richard from las vegas, NV
  • Easy
  • 1- 2 hours
  • Screw drivers, Socket set, Wrench (Adjustable)
took dishwasher out- put on table to work on-removed wire brace- disconected drain outlet- disconnected top drive seal- removed wire clip connector- removed motor unit----------------
installed new motor/drain unit--used new longer wire brac used adapter to connect electical leads-
tightened clamps and bingo it worked and didnt' leak. good job on the supplying of all the necessary adapers.
Was this helpful?
Thank you for voting!