36314194991 Kenmore Dishwasher - Overview

Diagrams for 36314194991

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Lower Rack Wheel Kit - 8 Pack – Part Number: WD35X21038
$59.57
Special Order
Lower Rack Wheel Kit - 8 Pack
★★★★★
★★★★★
(102)
Part #WD35X21038
If your dishwasher door will not close, is noisy when operating, or the dishes are not cleaning properly, you might need to replace one or more of the wheels. Each wheel and axle are made of plastic and fit into one another so they can be clipped on to the lower dishwasher rack.
Lower Front Dishrack Wheel – Part Number: WD12X271
$28.95
Special Order
Lower Front Dishrack Wheel
★★★★★
★★★★★
(6)
Part #WD12X271
This wheel is located on the front lower rack. It includes the axle. Sold individually.
Corner Tub Baffle - Lower Right – Part Number: WD8X227
$22.95
Special Order
Corner Tub Baffle - Lower Right
★★★★★
★★★★★
(4)
Part #WD8X227
This baffle fits the lower right hand corner of some dishwashers. It is black and has a matching left hand lower corner baffle. It is recommended that you replace and install both left and right at the same time.
Corner Tub Baffle - Lower Left – Part Number: WD8X228
$22.95
Special Order
Corner Tub Baffle - Lower Left
★★★★★
★★★★★
(38)
Part #WD8X228
The left and right side baffles should be installed/replaced at the same time. Right side baffle is sold separately.
Dishwasher Rack Slide End Cap – Part Number: WD12X10304
$105.18
Special Order
Dishwasher Rack Slide End Cap
★★★★★
★★★★★
(6)
Part #WD12X10304
The Rack Slide End Cap is a white one-inch plastic part which replaces the end cap for your dishwasher rack, preventing your rack from sliding too far. If you find the dish rack is causing the door to not close properly, it may be due to the part being worn out or damaged. All you need to complete this repair is a small flat blade screw driver. Simply pop out the cap with a smaller flat-blade screwdriver and snap the new one into place. If the rear cap needs to be replaced you will need to remove both front caps and slide the rack completely off for full access. It is important to note that this part is sold individually, and more than one may be required, depending on your repair. An inexpensive part, it can be a good idea to purchase several at a time to have on-hand when needed.
Drain Valve Shaft Seal – Part Number: WD8X181
$50.69
Special Order
Push On Nut – Part Number: WR2X7054
$13.95
Special Order
Push On Nut
★★★★★
★★★★★
(13)
Part #WR2X7054
This push on nut is for your dishwasher or refrigerator. As the name suggests, it pushes into place, rather than being screwed in. It is approximately half an inch in diameter and is made of stainless steel.
Silverware Basket (Grey) – Part Number: WD28X265
$115.40
Special Order
Silverware Basket (Grey)
★★★★★
★★★★★
(6)
Part #WD28X265
This silverware basket is gray.
Upper Roller and Axle - Kit of 4 – Part Number: WD12X10327
$38.00
Special Order
Upper Roller and Axle - Kit of 4
★★★★★
★★★★★
(10)
Part #WD12X10327
This is a kit of 4 upper rollers and axles.
Hinge Arm Link – Part Number: WD14X10009
$17.70
Special Order
Hinge Arm Link
★★★★★
★★★★★
(15)
Part #WD14X10009
The hinge link on your dishwasher connects the spring to the dishwasher door hinge. If the hinge link becomes cracked or damaged, you may not be able to shut or lock your dishwasher door properly. In this case, you will need to replace the hinge link. Pull out your dishwasher to inspect the hinge and spring, if the link is broken, it may be disconnected and on the ground already. If not, you can remove the hinge arm link by simply disconnecting it from the hinge and spring, then replacing it with the new part. The hinge arm link is a small piece of white plastic about an inch and a half long. It is sold individually, and is an OEM part from the manufacturer.
Rinse Aid Fill Cap – Part Number: WD12X10284
$78.79
Special Order
Rinse Aid Fill Cap
★★★★★
★★★★★
(5)
Part #WD12X10284
This part helps keep the rinse aid the dispenser until its needed.
Pump To Wash Arm Rubber Connector – Part Number: WD18X214
$72.67
Special Order
Pump To Wash Arm Rubber Connector
★★★★★
★★★★★
(6)
Part #WD18X214
This connector has female threads.

Common Symptoms of the 36314194991

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The rollers on the upper rack broke
545 of 576 people found this instruction helpful.
  • Carl from Fairfield, TX
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
There are eight guides that hold the rack rails in place. Use a Phillips screwdriver to remove the top two guides on each side in order to remove the rack from the dishwasher. The plastic axles on the rack and the rollers snap on. Use the hammer and punch to bend the metal clip on one end of the rail. Remove the plastic end piece the n slide the rollers out. Place two new rollers in the rail and put the plastic end piece on. Use the hammer and punch to bend the metal clip back into place. Snap the rails on the rack and set the rack on the guides in the dishwasher. Replace the top guide using the screwdriver, you will have to twist the rails in order get them in between the
guides.
Was this helpful?
Thank you for voting!
Lower rack wheel was melted
523 of 550 people found this instruction helpful.
  • Mark from Huntingdon Valley, PA
  • Really Easy
  • Less than 15 mins
Unsnapped clip,and moved it 90 degrees. Slip wheel and clip off. Installed clip on new wheel. replaced new wheel. The wheel did not come with a new clip and was not suggested on the parts list. The existing clip was still OK but if it was not, I would have had to order a clip and wait. All in all, a good experience.
Was this helpful?
Thank you for voting!
Wheel broken off bottom rack
503 of 520 people found this instruction helpful.
  • Julie from Maumee, OH
  • Really Easy
  • Less than 15 mins
Open the tiny plastic package in inserted the wheel onto the "axle". Opened the dishwasher, pulled out the bottom rack and snapped the wheel onto the rack. Done!
Was this helpful?
Thank you for voting!