3612BRA Makita Router - Overview

Included in part number 596141-3

Genuine Makita replacement part. rnThis phillips pan-head screw includes a washer. It is sold individually.

Genuine Makita replacement part, This item is sold individually. This screw is used mostly on the bases of the tool listed below. On the jig saws it is used to attach the Base Plate to the base. On the Router it is used to attach the Base Plate to the base On the Circular Saw it is used to attach the Depth Guide to the Base of the saw.

This item is available as an individual replacement part. The hex nut is made out of metal. A wrench might be helpful during the installation of this part. It might break or strip over time and will need replacing. This genuine item is supplied by the original equipment manufacturer for use with blowers, drills, grinders, nailers, rotary hammers, routers, sanders, saws, and trimmers made by Makita.

This item is a genuine Makita part that has been sourced from the original manufacturer to be used with trimmers, circular saws, sanders, routers, nailers, reciprocating saws, laminate trimmers, and planers. The flat washer is used with different types of power tools and the application of the washer can vary based on the model of the equipment. This item is available as an individual replacement part.

This is an authentic Makita replacement part that has been sourced from the original manufacturer to be used with circular saws, table saws, masonry saws, planers, demolition hammers, and angle cutters. The washer has multiple applications based on the model of the power tool. It is recommended to review your model's diagram to verify this washer's compatibility. The washer is sold individually.

It is a high-quality replacement part that is specially manufactured for use with Makita grinders. This retaining ring is used to secure the Pin 6, please make sure to check appropriate diagram of your model for correct location and use of this hardware. It is made of durable metal and it is sold individually, to remove this retaining ring it is best to use snap-ring pliers.

Genuine Makita replacement part, this item is sold individually. The purpose of the Brush Holder Cap is to retain the brush in the brush holder. This Brush Cap is used on all the Makita models listed below. It is removed by using a slotted screwdriver Do not press too hard when removing the cap they do have a tendency to break.

This cord is a genuine Makita replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Over time, power tool cords will wear out or become frayed. We recommend replacing a cord as soon as signs of wear are visible. Power Cord Specifications: • 2 Prongs • 2 Wires • 14 Gauge • 8 Feet Long

This is a Ball Bearing that is sealed on both sides. This is a genuine Makita replacement part that is sold individually. rnrn • Ball bearings minimize friction between 2 parts in your tool that would otherwise spin and rub against each other. The balls or rollers take the load and spin, distributing the weight evenly while the minimal ...Read morecontact area of the balls reduce friction. This reduces wear on the tool and allows it to run smoothly. rn • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

This is a Ball Bearing that is sealed on both sides. This genuine Makita replacement part is sold individually. • Ball bearings minimize friction between rotating parts in your tool. The balls or rollers bear the load and spin, distributing the weight evenly, while the minimal contact area of the balls reduces friction. This reduc...Read morees wear on the tool, allowing it to run smoothly. • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

This is an authentic OEM part. The Makita compression spring 7 is made for use with several router and grinder devices. The metal spring is often fitted in the motor bracket, providing tension to the pin. This component is sold individually. Please refer to the specific manual for repair instructions. No tools should be necessary for making the installation.