358798940 Craftsman Leaf Blower / Vacuum - Overview

Diagrams for 358798940

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Spark Plug – Part Number: CJ8Y
No Longer Available
Spark Plug
Part #CJ8Y
Ignition Module – Part Number: 530039137
No Longer Available
Ignition Module
Part #530039137
Bearing – Part Number: 530-032102
No Longer Available
Bearing
Part #530-032102
Retaining Ring – Part Number: 530-015789
No Longer Available
Retaining Ring
Part #530-015789
Blower Housing – Part Number: 530-014265
No Longer Available
Blower Housing
Part #530-014265
Drag Element – Part Number: 530-037716
No Longer Available
Drag Element
Part #530-037716
Knob – Part Number: 530-029484
No Longer Available
Knob
Part #530-029484
Choke Shutter – Part Number: 530035405
No Longer Available
Choke Shutter
Part #530035405
Piston – Part Number: 530069349
No Longer Available
Piston
Part #530069349
Owners Manual – Part Number: 530084330
No Longer Available
Owners Manual
Part #530084330
Decal – Part Number: 530-047758
No Longer Available
Decal
Part #530-047758
Carton – Part Number: 530-085371
No Longer Available
Carton
Part #530-085371

Common Symptoms of the 358798940

How this model fails, and the parts that fix it.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
installing fuel through fuel tank wall
11 of 18 people found this instruction helpful.
  • RICHARD from BROCKTON, MA
  • Difficult
  • More than 2 hours
  • Pliers, Screw drivers
To start, remove the plastic carburetor grill. DO NOT remove the carburetor. The fuel line has to be sliced down to fit through the tank hole and get it in far enough up into the tank to grab with needle nose pliers.( need long needle nose pliers which I didn't have) I placed about six inches of the plastic tubing in the jaws of vice so t hat half of the tube was squeezed in the vice jaws. I then used a razor blade to shave off the exposed tube. I slipped the shaved end of the tube up through the tank hole far enough to grab with long tweezers and pulled it up to where I could grab it in the tank with needle nose pliers. I put light lube oil on the remaining tubing and pulled it through. It takes a steady firm pull to pull it in. Install the filter and pull the tube back down into the tank. I also used a small diameter drill bit and with my fingers slightly reamed the tube ends to ease the tube over the filter and carburetor nipples. To prime the engine, spray starting fluid into the carburetor and start. Repeat until the engine will run on fuel. It took me hours to figure this out, but will take less than an hour with this method.
Was this helpful?
Thank you for voting!
Split fuel line driving brother-in-law to frustration
1 of 5 people found this instruction helpful.
  • Howard from UNICOI, TN
  • Really Easy
  • 30 - 60 mins
  • Pliers
Seven screw, three case cover, two air cleaner, two carb mounting, pulled carb, drained tank, pulled old fuel line, treaded new one in, wire to thread, thread to angle cut fuel line. Reassemble, test, sharpen chain, retest…not exactly a doityourselfer, graduate degree in mechanical/industrial engineering and former medium/heavy mechanica l. Get fuel line on carb prior to reassembly, line may need some stretching with a tapered punch.
Was this helpful?
Thank you for voting!