358796991 Craftsman Leaf Blower / Vacuum - Overview

Diagrams for 358796991

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Nut 8Pk – Part Number: STD541025
No Longer Available
Nut 8Pk
Part #STD541025
Champion Spark Plug Rcj-8y – Part Number: PM-2
No Longer Available
Flat Washer, 8Pk – Part Number: STD551031
No Longer Available
Flat Washer, 8Pk
Part #STD551031
This is sold as a set that contains eight washers. These parts attach to the tank and are made out of metal. They are genuine items that are supplied by the original equipment manufacturer for use with Craftsman air compressors. During replacement, it may require a wrench to help install these parts correctly. They will require replacing if they become bent or broken.
Screw 8Pk – Part Number: STD610602
No Longer Available
Screw 8Pk
Part #STD610602
Crankcase – Part Number: 530-010757
No Longer Available
Crankcase
Part #530-010757
Screw – Part Number: 530-015128
No Longer Available
Screw
Part #530-015128
Screw – Part Number: 530-035016
No Longer Available
Screw
Part #530-035016
Pin – Part Number: 530-035028
No Longer Available
Pin
Part #530-035028
Carburetor Assembly – Part Number: 530-069252
No Longer Available
Carburetor Assembly
Part #530-069252
Screw – Part Number: 530-015561
No Longer Available
Screw
Part #530-015561
Screw – Part Number: 530-015479
No Longer Available
Screw
Part #530-015479
Screw – Part Number: 530-015407
No Longer Available
Screw
Part #530-015407

Common Symptoms of the 358796991

How this model fails, and the parts that fix it.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
installing fuel through fuel tank wall
11 of 18 people found this instruction helpful.
  • RICHARD from BROCKTON, MA
  • Difficult
  • More than 2 hours
  • Pliers, Screw drivers
To start, remove the plastic carburetor grill. DO NOT remove the carburetor. The fuel line has to be sliced down to fit through the tank hole and get it in far enough up into the tank to grab with needle nose pliers.( need long needle nose pliers which I didn't have) I placed about six inches of the plastic tubing in the jaws of vice so t hat half of the tube was squeezed in the vice jaws. I then used a razor blade to shave off the exposed tube. I slipped the shaved end of the tube up through the tank hole far enough to grab with long tweezers and pulled it up to where I could grab it in the tank with needle nose pliers. I put light lube oil on the remaining tubing and pulled it through. It takes a steady firm pull to pull it in. Install the filter and pull the tube back down into the tank. I also used a small diameter drill bit and with my fingers slightly reamed the tube ends to ease the tube over the filter and carburetor nipples. To prime the engine, spray starting fluid into the carburetor and start. Repeat until the engine will run on fuel. It took me hours to figure this out, but will take less than an hour with this method.
Was this helpful?
Thank you for voting!
Split fuel line driving brother-in-law to frustration
1 of 5 people found this instruction helpful.
  • Howard from UNICOI, TN
  • Really Easy
  • 30 - 60 mins
  • Pliers
Seven screw, three case cover, two air cleaner, two carb mounting, pulled carb, drained tank, pulled old fuel line, treaded new one in, wire to thread, thread to angle cut fuel line. Reassemble, test, sharpen chain, retest…not exactly a doityourselfer, graduate degree in mechanical/industrial engineering and former medium/heavy mechanica l. Get fuel line on carb prior to reassembly, line may need some stretching with a tapered punch.
Was this helpful?
Thank you for voting!