358360690 Craftsman Chainsaw - Overview

Diagrams for 358360690

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Cylinder Shield – Part Number: 545045801
No Longer Available
Cylinder Shield
Part #545045801
Chain – Part Number: 545011805
No Longer Available
Chain
Part #545011805
European Housing Fan – Part Number: 545045905
No Longer Available
European Housing Fan
Part #545045905
European Baffle – Part Number: 545045701
No Longer Available
European Baffle
Part #545045701
Warning Decal – Part Number: 530059905
No Longer Available
Warning Decal
Part #530059905
Bar 16" – Part Number: 71-36626
No Longer Available
Bar 16"
Part #71-36626

Manuals & Care Guides for 358360690

Click to download

Common Symptoms of the 358360690

How this model fails, and the parts that fix it.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Both the Fuel line and the Engine fuel line, where dry rotted.
57 of 75 people found this instruction helpful.
  • Victor from SCOTTSVILLE, KY
  • Very Easy
  • 15 - 30 mins
  • Pliers, Socket set
1) While still attached to the fuel tank, I first sized up the old fuel lines with the newer fuel lines.
2) With a pair of needle nose players, I then removed the old dry rotted fuel ?? lines, from the fuel tank.
3) I cleaned the fuel tank and around the carburetor area, to insure that there was no debris, that could possibly fa ll into the path of the new fuel lines installation.
4) I then installed the smaller one of the fuel lines, so that it would be out of the way, of the larger fuel line. I Pulled the fuel line through the smaller hole in the fuel tank, with needle nose players. I pulled the smaller fuel line out through the fuel tank filler hole, attached the fuel filter to the smaller fuel line. I Made sure that the fuel filter was extended to the furthest end of the fuel tank bottom. Six inches in all. I then attached the smaller fuel line to the carburetor.
5) I Installed the larger fuel line, followed the same procedures as the smaller fuel line.
6) Both fuel lines where cut on an angle for easy installation. No lubricant was necessary.
7) I filled up the fuel tank with fresh fuel and oil, new air filter and spark plug. It started on the first pull. Amazing.
Was this helpful?
Thank you for voting!
Would not start , had been sitting for years,
11 of 13 people found this instruction helpful.
  • Sherri from BREAUX BRIDGE, LA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I did not write detail steps , basically remove old carb replaced with new one, reassembled started right up no adjustments were needed !
Was this helpful?
Thank you for voting!
installing fuel through fuel tank wall
11 of 18 people found this instruction helpful.
  • RICHARD from BROCKTON, MA
  • Difficult
  • More than 2 hours
  • Pliers, Screw drivers
To start, remove the plastic carburetor grill. DO NOT remove the carburetor. The fuel line has to be sliced down to fit through the tank hole and get it in far enough up into the tank to grab with needle nose pliers.( need long needle nose pliers which I didn't have) I placed about six inches of the plastic tubing in the jaws of vice so t hat half of the tube was squeezed in the vice jaws. I then used a razor blade to shave off the exposed tube. I slipped the shaved end of the tube up through the tank hole far enough to grab with long tweezers and pulled it up to where I could grab it in the tank with needle nose pliers. I put light lube oil on the remaining tubing and pulled it through. It takes a steady firm pull to pull it in. Install the filter and pull the tube back down into the tank. I also used a small diameter drill bit and with my fingers slightly reamed the tube ends to ease the tube over the filter and carburetor nipples. To prime the engine, spray starting fluid into the carburetor and start. Repeat until the engine will run on fuel. It took me hours to figure this out, but will take less than an hour with this method.
Was this helpful?
Thank you for voting!