358356241 Craftsman Chainsaw - Overview

Diagrams for 358356241

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
853 Plug – Part Number: CJ7Y
No Longer Available
853 Plug
Part #CJ7Y
18 Chain – Part Number: 91PX062G
No Longer Available
18 Chain
Part #91PX062G
Diffuser – Part Number: 530036102
No Longer Available
Diffuser
Part #530036102
Cover – Part Number: 530036133
No Longer Available
Cover
Part #530036133
Muffler – Part Number: 530069416
No Longer Available
Muffler
Part #530069416
Fan Housing Assembly – Part Number: 530069734
No Longer Available
Fan Housing Assembly
Part #530069734
Shaft Assembly – Part Number: 530014843
No Longer Available
Shaft Assembly
Part #530014843
Handle – Part Number: 530036087
No Longer Available
Handle
Part #530036087
Carton Contents Bag – Part Number: 530-014835
No Longer Available
Carton Contents Bag
Part #530-014835
Carton – Part Number: 530061474
No Longer Available
Carton
Part #530061474
Cylinder – Part Number: 530069578
No Longer Available
Cylinder
Part #530069578
Flywheel Nut – Part Number: 530016139
No Longer Available
Flywheel Nut
Part #530016139

Manuals & Care Guides for 358356241

Click to download

Common Symptoms of the 358356241

How this model fails, and the parts that fix it.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
installing fuel through fuel tank wall
11 of 18 people found this instruction helpful.
  • RICHARD from BROCKTON, MA
  • Difficult
  • More than 2 hours
  • Pliers, Screw drivers
To start, remove the plastic carburetor grill. DO NOT remove the carburetor. The fuel line has to be sliced down to fit through the tank hole and get it in far enough up into the tank to grab with needle nose pliers.( need long needle nose pliers which I didn't have) I placed about six inches of the plastic tubing in the jaws of vice so t hat half of the tube was squeezed in the vice jaws. I then used a razor blade to shave off the exposed tube. I slipped the shaved end of the tube up through the tank hole far enough to grab with long tweezers and pulled it up to where I could grab it in the tank with needle nose pliers. I put light lube oil on the remaining tubing and pulled it through. It takes a steady firm pull to pull it in. Install the filter and pull the tube back down into the tank. I also used a small diameter drill bit and with my fingers slightly reamed the tube ends to ease the tube over the filter and carburetor nipples. To prime the engine, spray starting fluid into the carburetor and start. Repeat until the engine will run on fuel. It took me hours to figure this out, but will take less than an hour with this method.
Was this helpful?
Thank you for voting!
Split fuel line driving brother-in-law to frustration
1 of 5 people found this instruction helpful.
  • Howard from UNICOI, TN
  • Really Easy
  • 30 - 60 mins
  • Pliers
Seven screw, three case cover, two air cleaner, two carb mounting, pulled carb, drained tank, pulled old fuel line, treaded new one in, wire to thread, thread to angle cut fuel line. Reassemble, test, sharpen chain, retest…not exactly a doityourselfer, graduate degree in mechanical/industrial engineering and former medium/heavy mechanica l. Get fuel line on carb prior to reassembly, line may need some stretching with a tapered punch.
Was this helpful?
Thank you for voting!