358352670 Craftsman Chainsaw - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
853 Plug – Part Number: CJ7Y
No Longer Available
853 Plug
Part #CJ7Y
Assy, Tool-less Knob – Part Number: 579107301
No Longer Available
Assy, Tool-less Knob
Part #579107301
This replacement OEM part is specially designed for Poulan chainsaws. It is the tool-less knob assembly that attaches to the chain brake assembly. The knob provides a user with a comfortable grip to adjust the chain tension. It has internal threads which allow it to be secured and removed without any tools. Check the owner's manual and the diagrams of your model for the correct application of this part. One durable component is included. Chain tension is very important. Chains stretch during use. This is especially true during the first few times you use your saw. Always check chain tension each time before you start the chainsaw.
Retainer – Part Number: 560024419
No Longer Available
Retainer
Part #560024419
Bar 18" 3/8 – Part Number: 578023116
No Longer Available
Bar 18" 3/8
Part #578023116
Chain 16" – Part Number: 71-36516
No Longer Available
Chain 16"
Part #71-36516
Chain – Part Number: 71-36517
No Longer Available
Chain
Part #71-36517

Common Symptoms of the 358352670

How this model fails, and the parts that fix it.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
installing fuel through fuel tank wall
11 of 18 people found this instruction helpful.
  • RICHARD from BROCKTON, MA
  • Difficult
  • More than 2 hours
  • Pliers, Screw drivers
To start, remove the plastic carburetor grill. DO NOT remove the carburetor. The fuel line has to be sliced down to fit through the tank hole and get it in far enough up into the tank to grab with needle nose pliers.( need long needle nose pliers which I didn't have) I placed about six inches of the plastic tubing in the jaws of vice so t hat half of the tube was squeezed in the vice jaws. I then used a razor blade to shave off the exposed tube. I slipped the shaved end of the tube up through the tank hole far enough to grab with long tweezers and pulled it up to where I could grab it in the tank with needle nose pliers. I put light lube oil on the remaining tubing and pulled it through. It takes a steady firm pull to pull it in. Install the filter and pull the tube back down into the tank. I also used a small diameter drill bit and with my fingers slightly reamed the tube ends to ease the tube over the filter and carburetor nipples. To prime the engine, spray starting fluid into the carburetor and start. Repeat until the engine will run on fuel. It took me hours to figure this out, but will take less than an hour with this method.
Was this helpful?
Thank you for voting!
Did not have handle
1 of 2 people found this instruction helpful.
  • Parker from LEVITTOWN, PA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
Unscrew the four screws and put the handle on and then put the screws back in
Was this helpful?
Thank you for voting!
Replaced pin bar adjuster
1 of 3 people found this instruction helpful.
  • Timothy from TRYON, NC
  • Really Easy
  • Less than 15 mins
A very simple fix once I rec'd the part. Took old broken part off bolt and screwed new one on. Great to get saw back in ready for use status.
Was this helpful?
Thank you for voting!