25358385893 Kenmore Refrigerator - Instructions

I turned the cap for the old filter and pulled it out . Then I put in the new one in and turned the cap to secure it in frig.

I removed the top shelf in the fridge. I then unscrewed the cover to the water filter and pulled the filter cartridge down into the cover. Keep the cover upright as there may be some water in it. I carried it to the sink. I took the new cartridge and ran water through it from the sink, then set it in the cover and took it to the fridge. I pushed the cartridge up into the space that I removed the old one from and screwed the cover back on. Then I took an empty pitcher and filled it from the water dispenser in the fridge door. I did this three times to charge the filter and remove charcoal dust. Water tastes great now. I ordered two filters so I would ony have to buy once a year. Great site to order the filters from. Cheaper than other sources and delivery was quick.

Fridge is a side by side. The freezer is pretty narrow for a guy with wide shoulders.

Pulled plug.

Had to remove bottom drawers then used nut driver to remove screws closest to back wall in drawer runners. Once the back screws were removed the runners could be swung up or down out of way so back cover could be removed.

Once back cover was removed thermostat was located attached to top pipe going into coil using a spring clamp.

Cut the wires just outside the crimp connectors going into thermostat. Released the spring clamp buy squeezing botton together.

Removed old badly corroded thermostat.

I wish I had attached the crimp connectors to the new thermostat wires before mounting it. Reaching way in the back, while turning shoulders verticly and trying to get the wire connectors set from both sides was awkward and uncomfortable...The biggest PIA of the whole task.

Once connected I let the fridge (thermostat) cool for 10 min. Turned the dial defrost timer to get it into defrost mode. Stupidly touched the heating element to see if it was getting warm...it was very hot.

Coils steamed...every looked like it was working. Unplugged, put back cover back on and retattached drawer mounts.

Plugged back in and everying is working great!

Unplugged faulty ice maker, removed two screws holding it to the refrigerator and took it out. Reversed the operation with the new ice maker and after a few minutes presto, we have ice.

It was really easy. All you have to do is twist the old filter out, stick in the new one and twist!

First i killed the power and water supply to fridge. Then i removed all the racks in freezer and the 1/4" screws for rack supports with nut driver. Next i removed the evaporator cover 1/4" screws to gain access. Then i removed the the 1/4" screw that holds the evaporator at the bottom and moved the evaporator outward to remove the heater element. Then i installed new heater element from the bottom of the evaporator making sure it was in the center of the evap coils.
Next i replaced the defrost thermostat cutting the old wires. Then stripped and crimpped the new thermostat in place making sure of the same installed postion as removed.
Next i replaced the defrost timer located at the bottom left using philips head screw driver.
Next i replaced the water filter by turning it counterclockwise to remove.
Then restored power and water supply. Next i tested the heater element by turning the dial on the defrost timer clockwise until it clicked and watched the element glow.
Then waited for the deforst thermostat to shut off the heater. Finally i checked the evaporator drain iin the back of fridge for blockage and cleaned out completely.
Repairs successful fridge good as new.

First I removed ice maker and tested the micro switches and motor individually. Then checked the resistance of the heater element, and the thermostat. All components tested okay and worked individually. However when installed in the freezer the motor would not turn. and if you manually turned the gear in front, which should cycle everything,nothing would happen. Finally, I found one part that I had not checked, the thermal cut-off, and upon removing it, one wire fell off the small square piece. This wire was corroded. I replaced the unit in about 10 minuites and ice maker is working perfectly again.

I'm too young to die so I unpluged the refriderator first. The cold control is mounted in a plastic housing at the top of the freezer compartment that is held in place by two screws on the back side. I removed them with a nutdriver. Pull off the knob and use a screwdriver to release the control from it's bracket and pull off the 3 wires noteing where they go. Slide the sensing element out and remove the plastic sleeve. Stragihten the sensing element on the new control and slide on the plastic sleve. Slide the sensing element in place, push the wires onto the terminals and snap the control into the bracket. Re-install the two screws and the control knob. Plug it in and you're done. It took longer to write this than to replace the control.

My freezer was frozen but my refrigerated side was not cooling, the temp was actually around 60-degrees. After inspecting i noticed no air was flowing through the vent from freezer side to fridge side. I removed everything from freezer and took the back wall panel off inside freezer section and immedietely noticed alot of ice on coils etc. After researching i found the defrost timer was not working and thus allowing frost and ice to build up on coils and block air flow. My defrost timer was located on the front bottom left behind kick panel, using a phillips screwdriver i removed 2 screws and then disconnected wire harness to the defrost timer. Then i inserted new defrost timer and connected wire harness and then put the 2 screws back in. My fridge is now working great and the ice build-up is gone and i am getting good air flow .. temps on fridge side are now between 32-34degrees. This was an easy project and saved me alot of money doing myself

Danger: Replacing these parts requires working with electrical wiring, be certain to unplug the refrigerator before starting work.

1. Unplug appliance
2. Empty freezer section
3. Remove shelves and Ice storage tray
4. Remove 6 screws from evaporator cover.
Note: Remember where the screws with insulated washers go.
5. Use a hair dryer to melt all ice from coil
Danger: To prevent injury or death from electrocution always ensure that the hairdryer does not get wet while in operation.
6. Unplug defrost heater and defrost thermostat wires
Note: Thermostat is wired in series with the heater.
7. Remove screw from white plastic holder located on top of evaporator coil
8. Remove styrofoam pieces from top of coil
9. Grasp the bottom of the evaporator coil and carefully lift and pull out the bottom end a few inches
10. Remove old heater coil by pulling out from the bottom and replace with new coil
Note: Be very careful when moving the evaporator, it is made of aluminum and will be very costly to repair if you damage the tubing.
11. Replace old thermostat with new thermostat
12. Re-connect thermostat and heater wiring
Note: Remember to route wiring so that condensation does not gravitate to the electrical connections.
13. You can check if the heater is working by manually rotating the defrost timer clockwise. The timer dial is located on the bottom, front of the refrigerator on the freezer side. Be careful, the heater gets very hot.
14. Re-install evaporator cover
15. Re-install shelves and ice storage tray
16. Plug in the refrigerator
Note: Depending on how warm your refrigerator was it may take 24 hours to return to normal operating temperatures.
Note: Take your time and the job will go faster.

First I pulled the ice tray out so I could see the solenoid housing/ice tray support(1 unit). Below the ice tray there are 2 screws that hold the solenoid housing/ice tray support. After removing those the assembly lifts up so you can see the wiring harness to disconnect. I pulled it out and removed the 2 screws to open it up. There is 2 screws holding the solenoid in place and one ground wire. This was an easy fix and I know I saved a lot of money.

Reviewed the video on your website and followed the directions to the letter. Great video

i removed the 4 screws holding cover. removed two screws holding timer. unplugged timer. plugged in new one. reassembled.

Loosen two screws, unclip electrical connection, remove ice maker, remove l shaped leveling piece of metal from old one, put on new one. Install in reverse order. Hint.. when loosening two screws, use a mirror

First, unplug the refrigerator since you're working with live wires.

Remove the 4 Philips sheet metal screws holding the plastic housing that holds the temperature control to the top of the refrigerator compartment. Pull the housing down then out since there is a tube on the housing where the water flows out the back of the refrigerator during the defrost cycle.

Remove the 2 Philips screws holding the defrost timer on the plastic housing. Pull the connectors off the old timer and attach them in exactly the same positions on the new defrost timer.

Attach the new defrost timer to the plastic housing with the 2 screws.

Reinstall the plastic housing, making sure the water tube is inserted into the back of the refrigerator wall.

Plug the refrigerator back in and you're done.