Models > 25320911002 > Instructions

25320911002 Kenmore Freezer - Instructions

All Instructions for the 25320911002
1 - 6 of 6
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Freezer would not shut off unless unplugged.
Removed old cold temperature control; tested with ohm meter and determined that the control was bad; ordered new cold control from PartSelect.com. Installed new cold temperature control with no problems; freezer is now running like new again!
p.s. I was very pleased with how fast I received my order from PartSelect.com!
Parts Used:
Temperature Control
  • Carol from Marquette, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
19 of 30 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
While defrosting freezer tossed the drain plug with ice and water into the sewer system.
Opened mailer and bag and place the drain plug into the drain. fit perfectly. In fact it is better than the one lost since the original needed a screwdriver or tool to remove the plug. This one has a flang or finger turner on it so that it can be removed. Also, does not interfere with items in bottom of freezer.
Parts Used:
Interior Drain Plug
  • paul from LISLE, IL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Freezer wouldn’t turn on.
Put the new temperature control unit in plugged freezer back in and immediately turned on. Very simple repair. Saved a lot of money not having to purchase new or call a repair shop.
Parts Used:
Temperature Control
  • Robert from HARDING, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Plastic shelf supports broken
Needed to remove both left and right broken (plastic) supports and reinsert the new parts. Not hard at all...worked like a charm!
Parts Used:
Shelf Support - Left Side Shelf Support - Right Side
  • shari from west sand lake, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
6 of 23 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Initially on full time then off full time
A 1,2,3 approach: 1, order the right part at the best price, Part Select has easy to navigate website and provides updated info on what will work in your appliance at a fraction of other site costs. 2. Configure the appliance to control the temp for a few days to save the food. This is accomplished by jumpering the two control wires to keep the compressor on and plugging the appliance cord into a timer with a 2hr on and 4hr off cycle. use the thermometer verify 0 degrees. 3. When the temp control is delivered unplug the power cord and proceed to repace the temp control, using care not to crimp the temp sensor bulb tubing. A #1 phillips screwdriver will release the control housing and temp sensor clamp assy. When complete set control to mid range and plug appliance into wall outlet. Use thermometer to set desired temp.
Parts Used:
Temperature Control
  • JOHN from Palmyra, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The frezzer ran continusly never shut off.
The installation was really simple, no problem. No instructions needed. What surprised me was, The new thermostat was installed in less then 24 hours after it was ordered. I live in FL
Parts Used:
Temperature Control
  • Calvin from New Port Richey, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 25320911002
1 - 6 of 6
Back to Top