2231 Frigidaire Range - Overview

Diagrams for 2231

See every part. Know exactly what you need.

Parts for the 2231

View More

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Flat Style Oven Igniter – Part Number: 5303935066
$56.05
In Stock
Flat Style Oven Igniter
★★★★★
★★★★★
(35)
Part #5303935066
This flat style gas oven igniter has an amperage range between 3.2 to 3.6. This part comes with two ceramic wire nuts.
Light Bulb – Part Number: 316538904
$35.95
In Stock
Light Bulb
★★★★★
★★★★★
(9)
Part #316538904
This 40-watt appliance light bulb is a reliable replacement for use in select ranges, refrigerators, freezers, and microwaves. It provides bright, consistent lighting to help you see clearly inside your appliance. Installation is simple—just unscrew the old bulb and replace it with the new one. If the existing bulb is broken, disconnect power and use needle-nose pliers to safely remove the remaining base. Sold individually, this bulb is a commonly replaced part—consider keeping a spare on hand.
Read less
Oven Light Socket – Part Number: 316116400
$75.74
In Stock
Oven Rack – Part Number: 316067902
$119.86
In Stock
Oven Rack
★★★★★
★★★★★
(2)
Part #316067902
Sold individually.
Thermostat Bulb Clip – Part Number: 5303284616
$21.95
Special Order
Thermostat Bulb Clip
Part #5303284616
REGULATOR – Part Number: 316091711
$113.66
In Stock
REGULATOR
★★★★★
★★★★★
(3)
Part #316091711
This is a genuine use wci regulator, which works with ranges.
Safety Valve – Part Number: 3203459
$359.52
In Stock
Safety Valve
Part #3203459
This safety valve ensures that no gas is released until the igniter has received the proper voltage needed to ignite the gas range.
Oven Bottom Panel – Part Number: 316495901
No Longer Available
Front Burner – Part Number: 5304506427
$122.30
In Stock
Front Burner
★★★★★
★★★★★
(1)
Part #5304506427
This is a front burner assembly for the stovetop on your range. It delivers the gas to the main cooking area by dividing it through the slots or holes in order to create an evenly burning flame. Take note that this is a front burner assembly. If you are looking to replace your rear burner assembly, see that in the related parts section. This model is roughly 8 inches long, 4 inches wide, and 4 inches thick.
Drip Pan - Large Burner – Part Number: 316011403
No Longer Available
Drip Pan - Large Burner
Part #316011403
Sold individually.
SCREW – Part Number: 5303300265
$32.01
Special Order
SCREW
Part #5303300265
Spark Module - 120V – Part Number: 5303912606
$205.66
Special Order
Spark Module - 120V
Part #5303912606
This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
View More

Exact Part matches for your search term

Flange – Part Number: 2231
No Longer Available
Flange
This part number matches the current model number 2231
Part #2231

Common Symptoms of the 2231

How this model fails, and the parts that fix it.

Gas igniter glows, but will not light
Fixed by
these parts
Fixing
Fixing
Show All
Little to no heat when baking
Fixed by
these parts
Fixing
Show All
Will Not Start
Fixed by
these parts
Fixing
Fixing
Fixing
Show All
Element will not heat
Fixed by
these parts
Fixing
Show All
Gas smell
Fixed by
these parts
Fixing
Fixing
Show All
Oven not heating evenly
Fixed by
these parts
Fixing
Show All
Little to no heat when broiling
Fixed by
these parts
Fixing
Show All

Videos related to models starting with 2231

Watch our pros, then fix it yourself.

Replacing the Oven Light Socket

Replacing the Oven Light Socket

Replacing the Oven Rack

Replacing the Oven Rack

View More
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven quit heating.
571 of 629 people found this instruction helpful.
  • John from Darlington, SC
  • Easy
  • 15 - 30 mins
  • Nutdriver
After reading up on the problem of the gas oven not lighting I decided I needed to install a new igniter. I had read where some people just pulled a panel off the back and installed a new one.. yeah, no such luck with this model so I had to crawl into the broiler drawer space [which I had to clean out first]. Note, if you wear trifocal g lasses you might as well close your eyes and replace it by feel because there is no way to tilt your head back enough to see what you are doing and still get both arms and your chest in a broiler. Also be sure to remove all cats and dogs from the area before starting. They seem to think they can help or it's a game of hide and seek and they want to hide with you.. they were no help at all.
Other than that, it was quite easy.
Read less
Was this helpful?
Thank you for voting!
Oven was difficult to light, then stopped lighting altogether
284 of 370 people found this instruction helpful.
  • Ritchie from Ithaca, NY
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
1. Turned off circuit breaker to stove
2. Removed the two screws holding down the floor of the oven (screws are at back.), and then lifted it out.
3. Removed the nut holding down the flame guard, and lifted it off.
4. Opened the bottom drawer.
5. Removed the protective cover in the back left of the oven at the bottom, first removing the one screw at the bottom that holds it. This reveals a white plug, presumably going to a fuse.
6. Disconnected the white plastic connector, lifting its front tab to release it.
7. The igniter wires go to two lugs that attach at the floor of the oven at the back (one goes via the now free white connector). Slide back the plastic lug covers and use pliers to pull off the lugs. Note that the wider one (on the right) goes to the top of the igniter, while the narrower one (on the left) goes to the bottom of the igniter via the white plastic connector.
8. Removed the two bolts holding the igniter.
9. At this point, the igniter comes out. Nice, since it means you can work on the wires in comfort.
10. Slide the flame retardant sleeves away from the igniter. I found in-line connections about 1.5 inches from the igniter, and cut the wires next to these (on the side away from the igniter, of course.), and stripped the final 3/8 inch. Shorten the wires on the replacement igniter so that they are 3 or 4 inches long, slide on the flame retardant sleeves, then strip the final 3/8ths inch. Use the provided caps to connect the wires. Bottom wire goes to the plastic connector, top wire goes to the wide lug.
11. Install the new igniter by connecting the lugs, sliding on their protective plastic sleeves, reconnecting the white plastic connector, screwing in the two igniter mounting screws, and reinstalling the corner cover. Put back the flame shield and floor of the oven. Turn on the circuit breaker, and it works!
Read less
Was this helpful?
Thank you for voting!
Oven Would Not Heat - Oven Ignitor Failure
156 of 233 people found this instruction helpful.
  • Peter from Fife Lake, MI
  • Easy
  • 15 - 30 mins
  • Screw drivers
I first looked up my Model Number on PartSelect.com and looked at the schematic as well as Trouble Shooted my problem.

Reading the posts by others how they Removed, Replaced, and Repaired their Oven Ignitors, I used their helpful info, and of course did mine.

1. Unplugged my Oven/Stove.

2. Removed botto m storage door to get access to cover plate.

3. Removed oven racks inside oven to gain access to and removed Flame Cover.

4. Removed Screw holding Oven Ignitor in place.

5. Unplugged Ignitor Plug from feed wird in Oven from underneath.

6. Removed Oven Ignitor from the bottom area where storage drawer was.

7. Installed new Ignitor and replaced screw holding Ignitor assembly in place.

8. Replace Flame cover and racks.

9. Plugged in new ignitor underneath, and replaced cover plate.

10. Plugged in Stove/Oven and Oven began to heat! IGNITOR worked!

11. Replaced bottom drawer and slid Stove back into position.

All went easy and only difficulty was replacing cover plate below as it is awkward and having to line up screws/holes was a bit trying.

Using Work Light essential to see well, and, some screws may or can be hard to remove.

Both my neighbor and I ordered our Ignitors within a week of each other. My Oven was Amana his is a Tappan. His failed after a few weeks, but, PartSelect replaced promptly and we are all happy.
Read less
Was this helpful?
Thank you for voting!
View More