2213804N710 Kenmore Dishwasher - Overview
Sections of the 2213804N710
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Dishwasher Rack Track Stop
PartSelect #: PS11746591
Manufacturer #: WP8565925
The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes properly, the rack s...
$14.95
In Stock
Dishwasher Friction Sleeve
PartSelect #: PS11745488
Manufacturer #: WP8268961
This part helps to keep your door quiet when it opens and closes.
$12.95
In Stock
Touch-Up Paint - White
PartSelect #: PS385132
Manufacturer #: 72017
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
$17.95
In Stock
Power Cord Kit
PartSelect #: PS358548
Manufacturer #: 4317824
Includes power cord and all necessary parts needed for complete installation of cord.
$28.55
In Stock
Dishwasher Drain Pump
PartSelect #: PS11738151
Manufacturer #: W10876537
This drain pump motor assembly is a key component in the dishwasher’s drainage system, responsible for efficiently removing water from the tub during the drain cycle. A malfunctioning pump can lead to...
$96.14
In Stock
Side Mounting Bracket Kit
PartSelect #: PS1487167
Manufacturer #: 8212560
This mounting kit can be used on solid surface countertops.
$34.95
In Stock
Dishwasher Water Inlet
PartSelect #: PS11750066
Manufacturer #: WPW10195536
This is connected to the water valve, is located on the side of your tub and allows water to enter your dishwasher.
***Note: This part does not include the inlet gasket - must order separately.
$97.43
In Stock
Float Assembly
PartSelect #: PS11753319
Manufacturer #: WPW10346525
Got a Whirlpool dishwasher in need of a new float assembly? Take a look at our genuine Whirlpool FLOAT-ASM. This little device is essential for your appliance's smooth operation and safety. It rises a...
$60.45
Special Order
Dispenser Mounting Bracket
PartSelect #: PS11755103
Manufacturer #: WPW10462232
$34.40
Special Order
Common Symptoms of the 2213804N710
[Viewing 9 of 9]Not draining
Fixed by
these parts
these parts
Show All
Door latch failure
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Not cleaning dishes properly
Fixed by
these parts
these parts
Show All
Will not fill with water
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Will not dispense detergent
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Door will fall down after opening
unscrewed dishwasher from cabinet ...,moved out slightly....while door closed ...reached with long nosed pliers door spring pulled forward...and allowing white plastic part that fits through sleeve and fit new sleeve over it...pulled spring attaching white plastic part and pushed unit back to cabinet and replaced screws DONE.
Parts Used:
-
Arthur from YORKTOWN HTS, NY
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
42 of 54 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Friction sleeve
-
Dave from PALM BAY, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
14 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dish washer would not drain properly
Shut off breaker. Took off front skirt of dishwasher .
Used pliers to loosen the pressure clamp on drain pump , have towel handy as there will be some water. Turn pump to left as you push in on the clip on side of drain pump. It will come out. Remove wire plug from old pump and plug into new pump than insert new pump and turn and push in till it clicks. Use pliers to pinch hose clamp and push hose onto pump release hose clamp. Turn breaker on. Run a cycle and make sure all is tight before putting skirt on front.
Used pliers to loosen the pressure clamp on drain pump , have towel handy as there will be some water. Turn pump to left as you push in on the clip on side of drain pump. It will come out. Remove wire plug from old pump and plug into new pump than insert new pump and turn and push in till it clicks. Use pliers to pinch hose clamp and push hose onto pump release hose clamp. Turn breaker on. Run a cycle and make sure all is tight before putting skirt on front.
Parts Used:
-
Kelli from BURLINGTON, MA
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
14 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!