1768 - Overview

Models starting with 1768

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
ELEMENT BAKE - RB147 – Part Number: WG02F05395
$135.45
In Stock
ELEMENT BAKE - RB147
★★★★★
★★★★★
(9)
Part #WG02F05395
This bottom oven bake element is designed for 30-inch electric ranges and ovens, delivering reliable and even heat for baking. Rated at 3000 watts and operating on 240 volts, it helps resolve common issues such as no heat, uneven heating, or a visibly damaged element. Installed at the base of the oven, it restores proper cooking performance when the original element fails. Always disconnect power before installation, and be sure to verify your appliance model to ensure proper fit.
Fluorescent Lamp/Bulb – Part Number: F26T8-CW-4
No Longer Available
Fluorescent Lamp/Bulb
Part #F26T8-CW-4
Leveling Leg – Part Number: WB2X8248
No Longer Available
Leveling Leg
Part #WB2X8248
SWITCH - WB23M107 – Part Number: WG02F05757
No Longer Available
SWITCH - WB23M107
Part #WG02F05757
Valve, Oil Drain – Part Number: 1723165SM
$38.95
Special Order
Valve, Oil Drain
Part #1723165SM
Fitting, Elbow, 3/8 Npt – Part Number: 186150GS
$26.95
Special Order
Fitting, Elbow, 3/8 Npt
Part #186150GS
Fuse, 2 Amp, 600 Volt – Part Number: 205110GS
$59.95
Special Order
Fuse, 2 Amp, 600 Volt
Part #205110GS
Solenoid, Gas Fuel – Part Number: 194683GS
$539.95
Special Order
Solenoid, Gas Fuel
Part #194683GS
This is a genuine Briggs & Stratton replacement part. The gas fuel solenoid is designed by the manufacturer for use in generators. This part is made primarily of metal, and is used to control the flow of fuel to the engine. You may require a wrench when replacing this item. This part is sold individually.
Handle, Door – Part Number: 186049GS
$9.95
Special Order
Handle, Door
Part #186049GS
Switch, Set Exercise – Part Number: 87799GS
$9.95
Special Order
Switch, Set Exercise
Part #87799GS
The set exercise switch attaches to the hour meter. This is a genuine Briggs & Stratton part sourced directly from the manufacturer for use in generators. This part is available as an individual replacement. It is made of plastic and metal and may require a wrench during installation. It might become broken and will need to be replaced.
Diode, Light – Part Number: B5133GS
$23.95
Special Order
Diode, Light
Part #B5133GS
Key, Lock – Part Number: B5053GS
$12.95
Special Order
Key, Lock
Part #B5053GS
This is an authentic manufacturer-sourced part which is specially made for Briggs and Stratton generators. It is an identical replacement for a missing or a faulty lock key that was included with a new unit, please make sure to refer to the appropriate diagram of your model for the correct location and application of this hardware. Keep in mind this high-quality item is made of durable metal and is sold individually.

Common Symptoms of models starting with 1768

How this model fails, and the parts that fix it.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
oven temperature too low
17 of 19 people found this instruction helpful.
  • Ryan from Henderson, NV
  • Easy
  • Less than 15 mins
  • Nutdriver
After ordering the proper part with the help of the phone customer service tech, I moved the stove from the wall, unclipped the connector, removed the two screws holding the sensor in place, and removed it. Reversed the above to put it back, and the oven holds perfect temperature.
Was this helpful?
Thank you for voting!
oven would not come up to temperature
14 of 17 people found this instruction helpful.
  • Clarence from Norwich, NY
  • Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Removed sensor from back wall of oven by removing 2 screws from flange. I could not pull the wire-nut connections out through the small hole and thought I would have to pull the whole oven out of the wall to acess the connections from the back so instead I clipped the wires close to the old sensor and connected the new sensor with the sma ll wire nuts provided, then enlarged the hole in the oven wall, being careful not to pinch the wires then pushed the wire nuts and extra wire back through the hole and put the screws back in the flange.
Was this helpful?
Thank you for voting!
remove and replace
10 of 24 people found this instruction helpful.
  • Perry from Flushing, NY
  • Really Easy
  • Less than 15 mins
very easy remove the bad bulb install the new one
Was this helpful?
Thank you for voting!