My Orders
171432-1 Briggs and Stratton Engine - Overview
Models starting with 171432-1
Click on the best match to narrow your results.
- 171432-1035-01 Briggs and Stratton Engine (Engine)
- 171432-1070-01 Briggs and Stratton Engine (Engine)
- 171432-1090-99 Briggs and Stratton Engine (Engine)
- 171432-1090-XX Briggs and Stratton Engine (Horizontal Engine)
- 171432-1100-01 Briggs and Stratton Engine (Engine)
- 171432-1105-01 Briggs and Stratton Engine (Engine)
- 171432-1111-01 Briggs and Stratton Engine (Engine)
- 171432-1121-01 Briggs and Stratton Engine (Engine)
- 171432-1123-01 Briggs and Stratton Engine (Engine)
- 171432-1124-01 Briggs and Stratton Engine (Engine)
Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".
Search filter:
Clear Filter
Your search term must have 3 or more characters.
$14.95
Special Order
Brace-air Cleaner
Part #224484
$33.95
Special Order
Puller-flywheel
Part #19203
This flywheel puller is designed for servicing larger small engines by safely removing tightly seated flywheels without stressing the crankshaft or damaging ignition components. Constructed from heavy-duty steel and engineered to apply even pulling force, it makes accessing the magneto, crankshaft key, or ignition system straightforward d...Read moreuring repairs or overhauls. Built to OEM specifications for durability and precise fit, it’s a reliable tool for maintaining lawn mowers, generators, and pressure washers with compatible engines.
Read less
$55.95
Special Order
Kit-carb Overhaul
Part #394693
An engine that surges, stalls, or will not stay running can have dirt or worn seals inside its float carburetor. This rebuild kit contains gaskets and small service pieces for restoring the carburetor rather than replacing the complete unit. Inspect the fuel supply and ignition system first, then confirm the engine identification and carb...Read moreuretor design. Work only on a cool engine in a ventilated area. Drain all fuel, disconnect the spark plug wire, and keep sparks and cigarettes away. Photograph the linkages, clean passages without enlarging them, install each gasket in the correct order, and check carefully for leaks before starting the engine.
Read less
$18.95
Special Order
Kit-needle/seat
Part #394682
This is an authentic manufacturer-supplied kit which is specially made for use with Briggs and Stratton engines that are commonly installed on a variety of lawn and garden equipment. This kit included the float needle and the needle seat. The needle and seat work like a valve to allow fuel into the carburetor bowl when the bowl drains and...Read more stops fuel intake when the bowl is full. To ensure the correct repair procedure, refer to the appropriate diagrams for your model.
Read less
$7.95
Special Order
Cap-oil Fill
Part #281658S
This manufacturer approved replacement part is specially produced for use with Briggs and Stratton engines commonly installed on Toro lawn and garden equipment. It is utilized to keep the oil in the tank. Please note this durable plastic oil fill cap is sold individually.
$54.95
Special Order
Nozzle-Carburetor
Part #398202
$70.95
Special Order
Clutch-starter
Part #399671
Hard starting may come from the recoil system instead of the carburetor or spark plug. If the rope pulls but the engine does not turn, the starter clutch may be worn, dirty, or jammed. The clutch turns the crankshaft during starting and lets go when the engine runs. First inspect the rope, rewind spring, pulley, flywheel screen, and clutc...Read moreh bearing. Confirm fit with the complete engine number. Remove the spark plug wire, wait for hot parts to cool, and keep dirt out of the bearing area. Test free movement before putting the shroud back on.
Read less
$196.95
In Stock
Motor-starter
Part #497595
This starter motor is for lawn and garden equipment engines.
Starter motor spins the flywheel to start the engine.
Wear work gloves to protect your hands when installing this part.
$13.95
Special Order
Keeper-valve
Part #494553
$48.95
Special Order
Arrestor-spark
Part #399541
$17.95
Special Order
Seal-oil
Part #294606S
This is an original replacement part manufactured for use with outdoor power equipment. The oil seal is used with a variety of different models of equipment and is commonly used to form a seal where camshaft or driveshaft exit the crankcase. This oil seal is sold as an individual replacement part, please see model diagram for associative parts.
$64.95
Special Order
Gasket Set-engine
Part #299577
It is a genuine replacement part that is supplied directly from the original equipment manufacturer for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. Gaskets are generally utilized to provide a tight seal between connected parts. It is an identical replacement for a missing or a faulty hardware that...Read more was installed on a new unit, please make sure to refer to the appropriate diagrams of your model for the correct location and use of these parts. Keep in mind this high-quality set is sold individually.
Read less
Common Symptoms of models starting with 171432-1
How this model fails, and the parts that fix it.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!
View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Gas tank leaking, pull starter rivets worn, rope and rope bushing worn
3 of 10 people
found this instruction helpful.
The gas tank was a simple job, close the fuel shut off, remove fuel hose then back out 2 bolts on the mounting bracket. Reverse procedure to mount.
To replace the pull starter/recoil assy. Remove low oil warning light, and air filter housing then remove the 4 bolts holding the front cover. Once the front cover is free remove kill sw ... Read more itch wire
Drill out the rivets holding the recoil housing w/ 3/16 bit. Screws w/ nuts are included to use in place of rivets, I used red Locktite on the screws which hold the started recoil to the front cover. Make sure the pull rope is correctly oriented in the 11:00 position. Replace front cover, four bolts. Air filter housing, kill switch wire and low oil warning light
To replace the pull starter/recoil assy. Remove low oil warning light, and air filter housing then remove the 4 bolts holding the front cover. Once the front cover is free remove kill sw ... Read more itch wire
Drill out the rivets holding the recoil housing w/ 3/16 bit. Screws w/ nuts are included to use in place of rivets, I used red Locktite on the screws which hold the started recoil to the front cover. Make sure the pull rope is correctly oriented in the 11:00 position. Replace front cover, four bolts. Air filter housing, kill switch wire and low oil warning light
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!